Chevy Oil pressure electrical problem - Reply to Topic

Reply to Thread

Post a reply to the thread: Chevy Oil pressure electrical problem

Your Message

 

Send Trackbacks to (Separate multiple URLs with spaces)

You may choose an icon for your message from this list

Please enter the name by which you would like to log-in and be known on this site.

Please enter a password for your user account. Note that passwords are case-sensitive.

Please enter a valid email address for yourself.

Human Verification

In order to verify that you are a human and not a spam bot, please enter the answer into the following box below based on the instructions contained in the graphic.


Additional Options

  • Will turn www.example.com into [URL]http://www.example.com[/URL].

Topic Review (Newest First)

  • 07-15-2012, 07:30 PM
    fastlife
    Replacing a dmax right now because I thought it was the sender or cluster. So dont assume and let it go like I did. Turns out all those crankcases full of diesel due to bad injectors took its toll on the bearings.
  • 05-01-2012, 07:54 PM
    californiadreamin
    Quote Originally Posted by the General View Post
    I'm having the same issue with my '06 Duramax (LLY). Think it'd be the sending unit?
    i have seen it once, 04 dmax lb7, failed oil pump
  • 12-07-2010, 10:47 AM
    IMPATIENT 1
    Quote Originally Posted by the General View Post
    I'm having the same issue with my '06 Duramax (LLY). Think it'd be the sending unit?
    generally dmax's with oil pressure reading issues turn out to be clusters, the sender on a dmax is a isuzu part, hardly ever go bad
  • 12-07-2010, 10:40 AM
    the General
    I'm having the same issue with my '06 Duramax (LLY). Think it'd be the sending unit?
  • 12-02-2010, 08:35 PM
    LSXINDUSTRIES
    If u need a sender, I have about 100 sitting in my garage PM me and ill ship ya one
  • 11-29-2010, 04:12 PM
    Hullshot
    same thing on my 05, chime, 0 oil pressure, 15 minutes and a new sender and its done.
  • 11-25-2010, 02:34 PM
    Some Kind Of Monster
    It was the sender. I had to do the whole job by feel as the sender is hard to get at. Deep well socket, swivel, and a couple extensions and the job is done. I can now see my oil pressure again. Thanks for the help!!
  • 11-24-2010, 12:35 PM
    Mr. C
    If it's not the sender and is the cluster F@#* harness. double check with your dealer. My wifes 03 yukon went out (even though it was out of warranty) we had less than 100k miles on it and they replaced-no charge.

    Good Luck
  • 11-24-2010, 11:48 AM
    IMPATIENT 1
    not really, kinda booger to get at but if you can borrow a oil pressure sender socket its a breeze. you may be able to get some channel locks on the base and pop it loose, once its broke loose it'll jus finger on out, they have alil compression washer that seals em up.
  • 11-24-2010, 11:47 AM
    Havasu Dreamin
    My 05 Suburban was showing no oil pressure. Had it towed to the dealer in Claremont and it ended up being a bad sender. I think it was around $400 to change it.
  • 11-24-2010, 11:41 AM
    Some Kind Of Monster
    You're the man! There isn't really a rodent problem here so I'm going to shoot for the sender being the issue. Any quick / easy ways to get at it?
  • 11-24-2010, 11:35 AM
    IMPATIENT 1


    Engine Oil Pressure Gauge
    The instrument panel cluster (IPC) displays the engine oil pressure as determined by the powertrain control module (PCM). The IPC receives a class 2 message from the PCM indicating the engine oil pressure. The engine oil pressure gauge defaults to 0 kPa (0 psi) or below if:

    • The PCM detects a malfunction in the engine oil pressure sensor circuit.

    • The IPC detects a loss of class 2 communications with the PCM.
  • 11-24-2010, 11:28 AM
    IMPATIENT 1
    with it chime'n like that i wouldnt think it was the cluster itself. the sender sends its signal to the pcm and the pcm sends it along to the ipc(cluster). the chime means what the ipc is getting from the pcm is showing to be too low a pressure. try a sender, bet itll fix ya up. could also be rats ate wires behind the intake near the sender, see'n that alot this time of yr
  • 11-24-2010, 11:19 AM
    Some Kind Of Monster

    Chevy Oil pressure electrical problem

    I know some of you know this truck like the back of your hand so hopefully someone can take the guess work out of what's going on here.

    2004 Chevy 1500 4x4 Silverado

    Originally the oil pressure gauge was pegged but now it goes from being pegged to 0 and back again at randon intervals. It also likes to "ding ding" and tell me the oil pressure is low. The oil pressure is not low (checked it) so this is an electrical issue.

    Is this typically a sender problem? chafed wire? gauge cluster?

    Thanks for any help!

Posting Permissions

  • You may post new threads
  • You may post replies
  • You may not post attachments
  • You may not edit your posts
  •  

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90