LinkBack URL
About LinkBacksWANTED FRONT and REAR ENGINE BELL housing MOUNTS FOR A 1972 Sanger Shovelnose ski hydro. Big block chevy, Need Actual mounts or a template to have them made with feet for stringer rails. Wanting to get this project going very soon. THANKS
Engine mounts
WANTED FRONT and REAR ENGINE BELL housing MOUNTS FOR A 1972 Sanger Shovelnose ski hydro. Big block chevy, Need Actual mounts or a template to have them made with feet for stringer rails. Wanting to get this project going very soon. THANKS
Last edited by swtd; 06-05-2012 at 06:13 PM.
what width? may be a dumb question, but V-Drive or Jet?
slot
87 eliminator
76 cole tr1-1/2
next boat crazy
new owner of the redneck yacht club
stockton, ca.
Hydro
Will measure stringer width tomorrow morning. thanksOriginally Posted by slotracer
mounts
Engine front and rear Mounts needed are 26 inches total width. motor mount holes 23 1/2 inches total
Last edited by swtd; 06-12-2012 at 04:58 PM.
are they for a rail kit or stringer mount?
slot
87 eliminator
76 cole tr1-1/2
next boat crazy
new owner of the redneck yacht club
stockton, ca.
Mounts
Rail mounts. Thanks send pic's of you have Em.
I have a set, I will measure them today and see what size they are. all mine measure 23" wide
Last edited by slotracer; 06-10-2012 at 10:39 AM.
slot
87 eliminator
76 cole tr1-1/2
next boat crazy
new owner of the redneck yacht club
stockton, ca.
holes
My stringer mount rail holes were previously all filled with glass looks like my 72 shovelnose had the motor mounts ran thru the stringers so I am need of mounts and L brackets instead..... 26 inches stringer inside to stringer inside....ANYBODYCan a rail kit be used instad of old bracket setup??? Drive line setup degrees? Maybe see Jim Wilks when ready??? Whats the best way to go here?
Last edited by swtd; 06-11-2012 at 03:31 PM.
I have templates at home but dont get home for a few days. I can trace you a set. The came of a rail mount set for a Hondo (those were 23"). The stringers in my Sanger are 26" too so I adjusted accordingly. Im going to make a set out of plywood first and trim as needed before I start cutting my Aluminium plates. V drive set up driven off the crank end not balancer. Let me know if you want a tracing or not.My stringer mount rail holes were previously all filled with glass looks like my 72 shovelnose had the motor mounts ran thru the stringers so I am need of mounts and L brackets instead..... 26 inches stringer inside to stringer inside....ANYBODY
Sure
Please trace me a set front rear as described and post pic of your boat..... will p.m you address.. THANK YOU.
PM sent back at you. Look what I did to a perfectly good boatWANTED FRONT and REAR ENGINE BELL housing MOUNTS FOR A 1972 Sanger Shovelnose ski hydro. Big block chevy, Need Actual mounts or a template to have them made with feet for stringer rails. Wanting to get this project going very soon. THANKS
Last edited by md-11mike; 06-11-2012 at 05:41 PM.
i have a rail kit
SORRY BABY...THATS JUST HOW I ROLL.........
FUGITIVE RECOVERY/BODY GUARD/PRIVATE INVESTIGATION/CHEATING SPOUSE/STALKER
there you go, old Mouzer should have the whole set-up for ya.
slot
87 eliminator
76 cole tr1-1/2
next boat crazy
new owner of the redneck yacht club
stockton, ca.
Wow
Sweet you got your hands full therePM sent back at you. Look what I did to a perfectly good boat
Posting Permissions
Reply With Quote
Digg This Thread