EFI Fuel Circulating Question..... - Reply to Topic

Reply to Thread

Post a reply to the thread: EFI Fuel Circulating Question.....

Your Message

 

Send Trackbacks to (Separate multiple URLs with spaces)

You may choose an icon for your message from this list

Register Now

Please enter the name by which you would like to log-in and be known on this site.

Please enter a password for your user account. Note that passwords are case-sensitive.

Please enter a valid email address for yourself.

Please select your insurance company (Optional)

Log-in

Additional Options

  • Will turn www.example.com into [URL]http://www.example.com[/URL].

Topic Review (Newest First)

  • 02-28-2008, 05:52 PM
    Sanger Pete
    We solved this problem by removing the aluminum fuel fills, drilling and threading them to accept a 1/2" X 5/16" hose barb where they normally extended below the sides. We reinstalled the fills and threaded in the hose barbs through the aluminum fills and then into a 90* fitting with a braided line down into the tank. We then ran the return through a switch to each of the tanks through the hose barb set up. The only problem is that you have to watch carefully when filling up the tanks because the returns do obstruct the fuel fills slightly.
  • 02-22-2008, 02:05 AM
    bordsmnj
    why is the fuel cooler never between the pump and the motor in these set ups? to keep the pump cool?good thread i'm learning .
  • 02-21-2008, 01:06 PM
    franky
    I use a merc PS cooler (the good one with the tube bundle) as a fuel cooler prior to return to the sep/filter head. They are like $95 and work just fine. If you don't do something to cool the fuel the pump/return looping of the fuel will just heat it up and cause problems.
  • 02-21-2008, 11:16 AM
    BDMarine
    The problem with returning the fuel to the seperator is that in July at Havasu the chance for vapor lock is very high. I had that problem all last summer. I am in the process of moving the returns to the tank fills with something similar to the ones shown earlier in this thread from CP. In a single engine/dual tank when it has already had fuel in it, make a flange with a return bung welded into it, it will look similar to a fuel sending unit. Make a gasket (fuel safe) and screw it to the top of the tank away from the pick-up. Then use the Imco 6 port fuel valve, 2 for the supply and 2 for the return. (liability disclaimer) Make sure the return is completely sealed with a gasket at the flange and where the screws go into the tank.
  • 02-21-2008, 10:39 AM
    Racer52
    I have been returning through a fuel cooler and then back to the water seperator. Never had an issue and the fuel going to the pump is always cooled somewhat from the -6 or -8 return line.

    Did this due to the duel tank issue and no bungs in the tank for return lines.


    Racer
  • 02-20-2008, 08:29 PM
    STV_Keith
    Here I put a tank fill and return hose point into my fuel tank. The return is a 3/4" bushing with a 1/4" NPT on the top, which connects to a 5/16" hose barb.



    The original return was into a y-fitting on the fuel tank fill.
  • 02-20-2008, 07:58 PM
    Brian
    Quote Originally Posted by Notalent View Post
    The customer im dealing with says that his tank does not have a return into the tank and noone will weld one in.....what happens in this case....? Will the IMCO Fuel Valve fix the dilemna?
    Uh, no. Returning to separator is best solution in this case. IMCO valve just allows you to switch between feed & return, but if the tank(s) has no return(s), you still need to go with something different. Big separator filter is best alternative to give most thermal mass to dissipate heat before reaching the carb/injectors. Not such a problem with smaller pumps, but the big high pressure EFI pumps can run pretty warm and add significant heat to the fuel.
  • 02-20-2008, 01:37 PM
    Outlaw
    Quote Originally Posted by Notalent View Post
    The customer im dealing with says that his tank does not have a return into the tank and noone will weld one in.....what happens in this case....? Will the IMCO Fuel Valve fix the dilemna?
    It is best to get the return fuel back to the tank. IMO
  • 02-20-2008, 08:36 AM
    cfm
    A lot of people return it back to the water seperator. Use one that has 4 ports (2 outlets, 2 inlets) and mount the pump after (and lower) the seperator. Use a normal fuel filter after pump.

    Mercruiser does this also, but uses a fuel cooler (looks + is like small oil cooler) to make sure there is no fuel heating issues.

    I have not done the above, but I have done the following on single tank applications : http://www.cpperformance.com/SearchR...CategoryID=379

    The fuel fill hoses I did these in where 2" ID. If you don't have this fill hose ID nor single tank, then this won't work for you.
  • 02-20-2008, 08:08 AM
    Notalent
    The customer im dealing with says that his tank does not have a return into the tank and noone will weld one in.....what happens in this case....? Will the IMCO Fuel Valve fix the dilemna?
  • 02-19-2008, 06:44 PM
    sanger rat
    I just split the lines back to the tanks. -10 to the regulator -8 out to two -6 lines. Never had a problem with tanks not being equal.
  • 02-19-2008, 06:02 PM
    Outlaw
    IMCO makes a really nice fuel selector switch/valve
    made just for EFI. 6 port. 1/2 " it swiches feed and return and
    sending units. pricey but nice

    http://www.danamarineproducts.com/Pr...TOKEN=59965491
  • 02-19-2008, 04:19 PM
    oldschool
    If your returning to the tanks just run your return line to a tank selector valve(just one to switch from left to right). From there you just make sure your returning from the same tank your pulling from.
  • 02-18-2008, 07:04 PM
    scott foxwell
    Quote Originally Posted by Notalent View Post
    Is there any reason why it wouldnt be able to dump back into the fuel tank?

    Thanks for the info.
    No, as long as you're running one tank. If it's a boat with two side tanks, it can be a problem with only one return line.
This thread has more than 14 replies. Click here to review the whole thread.

Posting Permissions

  • You may post new threads
  • You may post replies
  • You may not post attachments
  • You may not edit your posts
  •  
 

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95