Busy night working on the boat last night...some Q's - Reply to Topic

Reply to Thread

Post a reply to the thread: Busy night working on the boat last night...some Q's

Your Message

 

Send Trackbacks to (Separate multiple URLs with spaces)

You may choose an icon for your message from this list

Register Now

Please enter the name by which you would like to log-in and be known on this site.

Please enter a password for your user account. Note that passwords are case-sensitive.

Please enter a valid email address for yourself.

Please select your insurance company (Optional)

Log-in

Additional Options

  • Will turn www.example.com into [URL]http://www.example.com[/URL].

Topic Review (Newest First)

  • 08-19-2011, 05:24 PM
    Need4Speed77
    Quote Originally Posted by FormulaZR View Post
    Last night I added 4* of wedge (from JBP), new packing seals (from JBP), set ride plate at 2.6* from 3.2*, and swapped an RPM dual plane intake for a Super Victor intake - maybe a little more mph is in my future???

    On the packing seal, I have a question, how "snug" should it be?
    I keep hearing everyone say snug; but I've never done this before so I don't know how snug to get it...
    Like, where I feel a little pressure to turn; or just don't use brute strength, or what?


    Also, at 700-1000 rpm my pump makes a sound that is similar to, say, bolts/nuts being swirled in the bottom of a metal coffee can. It's not a knock or grind...but it is noise - is that the normal pump noise I hear about? Seems to go away at 1100 rpm. This was before the packing seal replacement - and I haven't run it since the seal was replaced because I don't run my boat out of water.
    Grease your u joints and see if the noise goes away, that is a very common area for people to forget about. As for the packings get them snug then put the boat in the water and tighten each nut equally til water drips one drop every 5 seconds or so. You dont want it to stream water and conversely dont want them to burn up by being too tight.
  • 08-19-2011, 12:42 PM
    watergun4u
    Quote Originally Posted by FormulaZR View Post
    Last night I added 4* of wedge (from JBP), new packing seals (from JBP), set ride plate at 2.6* from 3.2*, and swapped an RPM dual plane intake for a Super Victor intake - maybe a little more mph is in my future???

    On the packing seal, I have a question, how "snug" should it be?
    I keep hearing everyone say snug; but I've never done this before so I don't know how snug to get it...
    Like, where I feel a little pressure to turn; or just don't use brute strength, or what?


    Also, at 700-1000 rpm my pump makes a sound that is similar to, say, bolts/nuts being swirled in the bottom of a metal coffee can. It's not a knock or grind...but it is noise - is that the normal pump noise I hear about? Seems to go away at 1100 rpm. This was before the packing seal replacement - and I haven't run it since the seal was replaced because I don't run my boat out of water.

    The packing seals, you just want alittle presure on the bolts, go to tight it will crack or brake! the noise in the pump sounds to be to close of clearences, I would recheck you pump, you can look under the boat, throught the grate, or pull the grate and see if you can see or feel and damage to the wearring or impeller! Thats what I would do, Just my ,02,, oh and while you are looking, you should check the thrust bearing as well!
  • 08-18-2011, 06:17 AM
    FormulaZR

    Busy night working on the boat last night...some Q's

    Last night I added 4* of wedge (from JBP), new packing seals (from JBP), set ride plate at 2.6* from 3.2*, and swapped an RPM dual plane intake for a Super Victor intake - maybe a little more mph is in my future???

    On the packing seal, I have a question, how "snug" should it be?
    I keep hearing everyone say snug; but I've never done this before so I don't know how snug to get it...
    Like, where I feel a little pressure to turn; or just don't use brute strength, or what?


    Also, at 700-1000 rpm my pump makes a sound that is similar to, say, bolts/nuts being swirled in the bottom of a metal coffee can. It's not a knock or grind...but it is noise - is that the normal pump noise I hear about? Seems to go away at 1100 rpm. This was before the packing seal replacement - and I haven't run it since the seal was replaced because I don't run my boat out of water.

Posting Permissions

  • You may post new threads
  • You may post replies
  • You may not post attachments
  • You may not edit your posts
  •  
 

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95