[SOLD] V-drives>>> c500/hallcraft/and a z-drive/used parts caps cases shafts ect
Closed Thread
Page 1 of 2 1 2 LastLast
Results 1 to 14 of 23

Thread:
V-drives>>> c500/hallcraft/and a z-drive/used parts caps cases shafts ect

  1. #1
    Senior Member Mouzer's Avatar
    Join Date
    Mar 2008
    Location
    corona ca
    Posts
    19,674

    Default V-drives>>> c500/hallcraft/and a z-drive/used parts caps cases shafts ect

    C500.....$500 REDUCED COMES WITH XTRA SET OF CASES ​...SOLD
    PM ME
    Z-DRIVE .....$700 REDUCED
    make offer

    HULLCRAFT....$200 ..........sold

    used cases 10* 12* c500 ..........$100 ALL .sold

    caps

    caps w/tach drives SOLD

    in/out cases and handles IN OUT CASES SOLD HAVE A FEW NEW

    used mid plates for casale

    Last edited by Mouzer; 02-13-2018 at 01:40 PM.


    ''''''OWNER OF THE BIG WHITE WOLF....,,,
    ,,,
    Quick reply to this message Reply  

  2. Remove Advertisements
    PerformanceBoats.com
    Advertisements
     

  3. #2
    Senior Member capnfyr's Avatar
    Join Date
    Jun 2011
    Location
    Middleton, Idaho
    Posts
    737

    Default C 500 Ratio?

    Hey Mouze, do you happen to know what the ratio is in that C 500 gear case?
    Capnfyr
    1984 Daytona Sprint. AKA "Pyro Flyer" 2016 APBA High Points GPS 95 Champion.
    GN 8 AKA "Tinman" Under Construction. Back on the water for 2018.
    21' Eliminator Sport V Drive Lake Cruiser


    [SIGPIC]
    Quick reply to this message Reply  

  4. #3
    "The" masheenist wsuwrhr's Avatar
    Join Date
    Dec 2007
    Location
    Living in Alta Loma, working in Upland
    Posts
    5,444

    Default

    Quote Originally Posted by capnfyr View Post
    Hey Mouze, do you happen to know what the ratio is in that C 500 gear case?
    This.
    Last edited by wsuwrhr; 10-27-2017 at 11:34 AM.
    SB Products:Inspiring metal to change shape, one chip at a time.
    Good labor isn't cheap, cheap labor isn't good.
    The United States, the new and improved Roman Empire.
    Buy American made goods whenever you can, the job you save may be your own.

    Quick reply to this message Reply  

  5. Remove Advertisements
    PerformanceBoats.com
    Advertisements
     

  6. #4
    Senior Member Mouzer's Avatar
    Join Date
    Mar 2008
    Location
    corona ca
    Posts
    19,674

    Default

    Quote Originally Posted by capnfyr View Post
    Hey Mouze, do you happen to know what the ratio is in that C 500 gear case?
    i was told 32%


    ''''''OWNER OF THE BIG WHITE WOLF....,,,
    ,,,
    Quick reply to this message Reply  

  7. #5
    Senior Member Mouzer's Avatar
    Join Date
    Mar 2008
    Location
    corona ca
    Posts
    19,674

    Default



    ''''''OWNER OF THE BIG WHITE WOLF....,,,
    ,,,
    Quick reply to this message Reply  

  8. #6
    "The" masheenist wsuwrhr's Avatar
    Join Date
    Dec 2007
    Location
    Living in Alta Loma, working in Upland
    Posts
    5,444

    Default

    Quote Originally Posted by Mouzer View Post
    i was told 32%
    Quote Originally Posted by Mouzer View Post
    You've already got tape on the input shaft. Get to turnin.
    Last edited by wsuwrhr; 10-30-2017 at 07:48 PM.
    SB Products:Inspiring metal to change shape, one chip at a time.
    Good labor isn't cheap, cheap labor isn't good.
    The United States, the new and improved Roman Empire.
    Buy American made goods whenever you can, the job you save may be your own.

    Quick reply to this message Reply  

  9. #7
    Senior Member Mouzer's Avatar
    Join Date
    Mar 2008
    Location
    corona ca
    Posts
    19,674

    Default

    10 turns was 32 ...........so 5 would b 16


    ''''''OWNER OF THE BIG WHITE WOLF....,,,
    ,,,
    Quick reply to this message Reply  

  10. #8
    Or Seth, either one Budweiser's Avatar
    Join Date
    Dec 2007
    Location
    Tower Park Resort, Lodi, CA
    Posts
    3,270

    Default

    Quote Originally Posted by Mouzer View Post
    10 turns was 32 ...........so 5 would b 16
    Ummm

    Wouldn't those #'s indicate 320% OD?

    10 turns with 32% gears would equate to 13.2 turns of the output... or real close to 6.5 turns output with only 5 in.

    Whatever you guys are smoking... must be good shit hahaha

    I must be missing some sort of inside joke. You guys know your shit.
    Last edited by Budweiser; 10-30-2017 at 04:10 PM.
    Quick reply to this message Reply  

  11. #9
    Senior Member Mouzer's Avatar
    Join Date
    Mar 2008
    Location
    corona ca
    Posts
    19,674

    Default

    hahahahahahahah not 30 turn 13
    Last edited by Mouzer; 10-30-2017 at 04:23 PM.


    ''''''OWNER OF THE BIG WHITE WOLF....,,,
    ,,,
    Quick reply to this message Reply  

  12. #10
    "The" masheenist wsuwrhr's Avatar
    Join Date
    Dec 2007
    Location
    Living in Alta Loma, working in Upland
    Posts
    5,444

    Default

    Quote Originally Posted by Budweiser View Post
    Ummm

    Wouldn't those #'s indicate 320% OD?

    10 turns with 32% gears would equate to 13.2 turns of the output... or real close to 6.5 turns output with only 5 in.

    Whatever you guys are smoking... must be good shit hahaha

    I must be missing some sort of inside joke. You guys know your shit.
    I was just doing mathematical calc based on the numbers. Figured 5 turns of the top to 16 turns of the bottom makes .32. I was reprimanded already.

    Obviously I was way off.

    Brian
    Last edited by wsuwrhr; 10-30-2017 at 07:05 PM.
    SB Products:Inspiring metal to change shape, one chip at a time.
    Good labor isn't cheap, cheap labor isn't good.
    The United States, the new and improved Roman Empire.
    Buy American made goods whenever you can, the job you save may be your own.

    Quick reply to this message Reply  

  13. #11
    "The" masheenist wsuwrhr's Avatar
    Join Date
    Dec 2007
    Location
    Living in Alta Loma, working in Upland
    Posts
    5,444

    Default

    If I had it in front of me I could figure it out...I think.

    Isnt this right?

    Mark the top and bottom shafts. Rotate the top shaft and counting the turns of each shaft until the top and bottom shafts line up again.

    In UCH, the input shaft turns 25 rotations and the output shaft turns 24 times until they both line up again, 24/25 is .96 underdriven.

    I guess I will go sit back down and wait for the smart kids to speak up.

    Brian

    Quote Originally Posted by Budweiser View Post
    Ummm

    Wouldn't those #'s indicate 320% OD?

    10 turns with 32% gears would equate to 13.2 turns of the output... or real close to 6.5 turns output with only 5 in.

    Whatever you guys are smoking... must be good shit hahaha

    I must be missing some sort of inside joke. You guys know your shit.
    Last edited by wsuwrhr; 10-30-2017 at 07:27 PM.
    SB Products:Inspiring metal to change shape, one chip at a time.
    Good labor isn't cheap, cheap labor isn't good.
    The United States, the new and improved Roman Empire.
    Buy American made goods whenever you can, the job you save may be your own.

    Quick reply to this message Reply  

  14. #12
    Senior Member Mouzer's Avatar
    Join Date
    Mar 2008
    Location
    corona ca
    Posts
    19,674

    Default



    ''''''OWNER OF THE BIG WHITE WOLF....,,,
    ,,,
    Quick reply to this message Reply  

  15. #13
    Member oughtabeboatin's Avatar
    Join Date
    Apr 2012
    Location
    Vancouver, WA
    Posts
    77

    Default

    wsuwrhr is correct. if 10 turns on top shaft equals 32 turns on prop shaft it is 320% overdrive. Pretty unlikely. Better check again. Measure twice Cut once.
    Quick reply to this message Reply  

  16. #14
    "The" masheenist wsuwrhr's Avatar
    Join Date
    Dec 2007
    Location
    Living in Alta Loma, working in Upland
    Posts
    5,444

    Default

    Quote Originally Posted by oughtabeboatin View Post
    wsuwrhr is correct. if 10 turns on top shaft equals 32 turns on prop shaft it is 320% overdrive. Pretty unlikely. Better check again. Measure twice Cut once.
    My Bad.

    Mouser came by today for me to look over the billet cases and figure out how many 8 and 10 degs cases he has and I asked him to bring the C500 as well so I could redeem myself.

    We rotated the top shaft 3 revs and the bottom rotated 4 revs, so she has a 32% overdrive in her.
    Last edited by wsuwrhr; 10-31-2017 at 01:27 PM.
    SB Products:Inspiring metal to change shape, one chip at a time.
    Good labor isn't cheap, cheap labor isn't good.
    The United States, the new and improved Roman Empire.
    Buy American made goods whenever you can, the job you save may be your own.

    Quick reply to this message Reply  

Closed Thread
Page 1 of 2 1 2 LastLast

Quick Reply Quick Reply

Register Now

Please enter the name by which you would like to log-in and be known on this site.

Please enter a password for your user account. Note that passwords are case-sensitive.

Please enter a valid email address for yourself.

Please select your insurance company (Optional)

Log-in

Digg This Thread

Posting Permissions

  • You may post new threads
  • You may post replies
  • You may not post attachments
  • You may not edit your posts
  •  
 

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95