Search Results for ‘aluminum’

New Fresh 505" aluminum head standard deck BBC Long Block I had built for my sanger Drag runner , injury forced sale of boat and now motor . Built by Local very reputable Professional High Performance Motor builder , Virgin 4 bolt standard deck BBC .100 over New eagle forged rotating...

I bought this nice aluminum fuel tank a couple of years ago from Dave Sammons but never used it. After installing it in my shallow side board GN (El Cid) hull it was just too tall and didn't look right. So it's up for sale. Measurements are 22" tall 35" wide and 18" front to back. According to...

BB chevy clean but needs to be polished. these are real nice asking 125 for the pair with clamps obo.

Like new BOUY holders - See these new for $175 each Make offer - Located in Murrieta, CA near Lake Elsinore. Also go to Lake Havasu a lot. Thanks, Colby [email protected]

Selling KE cast aluminum oil pan fits mark 4 motor $325.00 + shipping Also Dyno time only Hays billet flywheel #10-130 Summit $319.95 asking $150.00 + shipping

WTB Aluminum Valve Covers w/ breathers offset to one end similar those below. Anybody have anything similar they're looking to get rid of? Russ, (562) 858-6926

WTB Aluminum Mark IV V-Drive (flywheel forward) Oil Pan. Olson, Stef's, Armando's, Aviad, etc. I'm aware of what is posted for sale, looking to see if there is anything else out there. Preferably with oil returns for turbos but not required. Russ, (562) 858-6926.

Need two. 4150.

PN: 06-8014 IMCO Aluminum "T" Tank 8 Gal. Aluminum "T" Tank 10" x 24" 8 Gallon with Brackets (tank in great condition with no dents or scratches) Fresh polish and black anodizing in great condition. (pictures dirty sorry) Also includes custom stringer mounts / tank risers (+/- 24" spread)...

8 gallon IMCO big sump "T" tank powdercoated silver vein. Great condition. 3/4 NPT outlet and three 3/8 NPT returns. Tank part number 06-8014 mounts 06-9071. Tank dimensions 10" diameter 24" wide 22" tall top of vent to bottom of sump. $350 Free Shipping. New Port Richey, Fl. Call or text 918...

2 New, old stock spun aluminum round gas tanks, been up in rafters 30 + years, never been mounted or had gas in them, 10 gal. Center of gas neck 16 1/2 inches from front of tank, comes with (4) SS mounting brackets, all $400.00 new price $350.00 for the pair, picked up only no ship, Jim...

NEW CO2 Bottles from Catalina Cylinder 10oz @ 110 2 1/2lb at 150 Leave a reply here or a pm Thanks

SB Chevy Weiand round finned aluminum exhaust manifolds with turndowns have only seen one other pair of these, very old, they were in a 64 flatty, $350.00 Jim 181890-867

I understand there will be no easy way to do this but I have a lot of aluminum to polish while in the boat. Any tips to help make my life easier that I would probably make it...

Please contact me, live way up north in Canada will pay for shipping nd everything else needed. If you have a set you don't need I'd love to take them off your hands for you. Thank you. You can PM me or call/text 519 240 1778.

15000 Price OBO. This came out of a 18' California Performance gullwing (Butterscotch color seen at Aha Quin Regatta). Minimal hours on since rebuild. 496 All aluminum jet boat set up motor for the river. Made 825HP at 6500RPM. Have build sheets and dyno sheets upon request. Ready to run all...

I have a pair of Eddie Marine EMI Thunder aluminum risers for their center mount manifolds. These have had about 4" of extra length added to the exhaust tube that can be removed. These risers take a 4" exhaust hose and the bolt pattern is 4-3/4" by 3". These fit the EMI Thunder manifolds for...

Block has new sleeves 4.5, fresh cut deck , .842 lifter bores in good shape. Been sitting most of its life. Never any damage. Steel splayed caps. located in shreveport, louisiana 318-687-9088 or 318-470-1482 $3500

Set of 8 brand new never used Bill Miller Engineering (BME) aluminum connecting rods, part number 396400. These are still in their original box, just sitting on the shelf and we will not be using them so up for sale they go. Manufactured using the BME 396 raw forging and as a 0.400" long BBC...

I have run flexplates in the past with no problems but on this Sanger project we are running GM 572/720 HP motor. It is internally balanced. It came with a steel flywheel which obviouslyI don’t want to use. Should I go to an Aluminum Flywheel or would a good quality Flexplate be ok?