Performance Boats Forum banner

angle

  1. Parts for Sale
    Paragon V Drive Transmission Angle Housing Scarce Paragon V Drive Transmission Angle Housing in great condition. No cracks, damage or alterations. It is marked W-12084 as pictured. $225 + ride Paypal only Please PM or email Thanks Jeff
  2. Jet Boats
    I'm wrapping up the mechanical work on the Canyon, so I started thinking about the setup. While I don't know the impeller or HP, I do know the loader is a blocker with the ramps flush with the keel. The shoe is a bit odd, but essentially a flat shoe. The ride plate is only 1* up but I'm used to...
  3. GN7 On the Dyno
    You guys running the really quick and fast mph setups in 19' Daytonas , Liberators ,Cheyennes > taking the bottom of the keel / intake as say a flat plane and Measurement (A) Ride Plate angle up from intake ...as measurement (B) Nozzle angle ( up or down in relation to keel / intake as (C )...
  4. Parts for Sale
    Looking for some stainless angle cut exhaust tips 4 "
  5. V-Drives
    In the spirit of continual testing I mounted the video camera off my ski tow pointing aft to see what was going on back there. First impression is "man that wake looks big" and then it dawned on me the camera was hanging upside down and only about 16" off the floor. I'm not thinking I'm getting...
  6. Outdrives
    I have built a stern drive hot rod from a outboard boat. Running a 300 he Chevy alpha. The trim is a just ed exactly to 21 inches at the trim pistons. If I trim up a touch more with the trail or switch I gain more speed. ? Is does the transom angle matter in the trim measurement. My transom...
  7. V-Drives
    What degree angle should motor be when stringers are level? Need to make new plates
  8. V-Drives
    Thought I saw somewhere that there's a formula to find the strut angle with some measurements. Anyone out there that can tell me the formula or what my strut angle is? Top front of strut barrel measures 2 3/4" to bottom. Back measures 5 1/8". Barrel measures 18" OAL. Thanks:))THumbsUp
  9. Outdrives
    Didn't see any other place to post this so I'll ask here. I've been looking at lots of pictures of used boats with trim tabs. It looks like some are mounted such that the bottom of the plates are horizontal and some are mounted at at the same angle as the V in the bottom of the boat. So I'm...
  10. Political Rhetoric
    AMAZING NRA Obama and the democrat party did not see this coming...... https://www.youtube.com/watch?feature=player_embedded&v=9RABZq5IoaQ
  11. Parts for Sale
    I need a angle adapter for a Casale gear box like the one in the pic BUT .... I need it to be a 1 to 1 adapter. The one in the pic is a Stewart Warner and it's stamped .500 and it doesn't work with my Jones tach that Valley Speedo and Tach just rebuilt to 1 to 1 specs :duh: Thanks David
  12. Jet Boats
    I have a buddy with a 1977 Hondo T-deck Jet boat 17.5'. Looks like it shoulda been a v-drive but the original owner set it up as a jet. He is in the process of restoring it, and we are going to be resetting the intake soon. Any recommendations on intake angle? I havent found anything...
  13. Greg Shoemaker
    I had to remove my intake (old putty) 0n my 1975 18 ft KURTIS 500 jetboat and had it machined for a shoe. when i went to reinstall it i noticed the the center area between stakes (keel) start to come up about 20 in. in front of the intake about 1/4 in. and goes back down to true keel at the...
  14. V-Drives
    Whatcha think of our new prototype idea? No permanent attachment... Test day was a little windy/rough... Using remote microphone for sound next test... Just learning the video editting so go easy on me...
  15. Jet Boats
    Does anyone sell a tool /spacer so you can square to the nozzle bushing to use an angle finder to set the nozzle angle on a place diverter FTN ?? I can make 1 but if they're cheap I just thought I would buy 1 ??????????
  16. GN7 On the Dyno
    OK, so when I dropped my distributor, I noticed it doesn't sit flat on the intake. A quick google search shows that a BBC distributor is actually at a 5* angle. I've never notice this before, or at least to this extreme visually. I measured my dist with a digital angle finder and sure enough...
  17. Jet Boats
    ok so i have adjusted my cable for my diverter and i cant seem to get it to toss up a roost.. not that i really need to do so but after i get my boat up on plane i might want to squirt some folks.. if the adjustment on the diverter is maxt out can i adjust it some more at the t handle...
  18. WFL Crew
    Hi guys this is my first post on here! I have a 1984 tx-19 with a blown 468 BBC In it and I have a ride plate question. What are you guys run for a average up angle? Right now I can not remember what I set mine at right now but I am thinking 3 deg up. I am just looking for a little more top...
  19. Parts for Sale
    need to clear "thumper" headers
  20. Jet Boats
    i have been looking at a chart that shows differences between impeller size and small dia and machine angle. its stated as such size...... small dia..... mach.ang. aa........ 7-7/16"....... 57-1/2 deg a......... 7-1/4"......... 60 deg b...
Top