Performance Boats Forum banner

Discussions Showcase Albums Media Media Comments Tags Marketplace

1-19 of 31 Results
  1. Parts for Sale
    Brand new billet, key way installed never used only as a mock up minus post , 200 plus shipping Adam 619 2479921
  2. Parts for Sale
    Looking for a standard flat tiller arm for a berkley pump,,,,,,,,
  3. Parts for Sale
    Anyone has a tiller arm out there? I'm running a droop so an offset one is fine or a standard flat one with a long shaft or even no shaft let me know,Thanks
  4. V-Drives
    This 1 1/8" Tiller Arm was designed for Schiada Boats. Beautifully machined from 303 Stainless Steel round bar for strength. It measures 6" long from the 1 1/8" diameter rudder bore to the two 1/2" diameter heim joint holes. A 1/4" standard keyway is used to fit your rudder. Featuring two 3/8"...
  5. Jet Boats
    Anybody have a picture of the calgo tiller arm used with a place diverter? I have a tiller arm that is gull shaped and am concerned it won't work with a place diverter type control. I assume there is a clearance issue between the width of the t. arm and the hyd. ram actuator bracket. thx
  6. Parts for Sale
    $100 plus the ride
  7. Parts for Sale
    Nozzle has yellow insert that is a bit worn. Bottom has been welded and smoothed. $140 located in Valencia CA PM me here or email [email protected]
  8. Parts for Sale
    Hello. I am looking for a used place diverter control arm for forward and reverse cable hook up. Thanx for any help. Also needing ball seal for diverter. Thank Mel
  9. GN7 On the Dyno
    I have a set of crane gold rocker arms with 0410 stamped on them. Cant find a cross reference to them....anyone know what the application or ratio is for the ?? Thanks.
  10. Parts for Sale
    I need a used 7/8" control arm for a cav rod. No aluminum. Don't need new, for my 83 yr old dads boat. Anybody have something laying around?
  11. GN7 On the Dyno
    How much clearance do I need between rocker arm and valve spring retainer?.
  12. Parts for Sale
    Nice calgo steering arm $65 shipped
  13. Jet Boats
    Before I get in there and just start beating the thing to death I though I would ask first prior to pounding on it...What's the best way to remove it...I know the key has to come out..see how the arm has slipped for some reason. I noticed it a couple of months ago and it was down about 1/16 and...
  14. Parts for Sale
    Need the arm for an air shifter on the v drive.It's the splined piece and want it in good shape. Needed immediately thank you
  15. Parts for Sale
    new BDS polished billet aluminum idler arm fits 3 & 3/8" o.d. snout $80. plus the ride
  16. GN7 On the Dyno
    Hi guys a newbi here as far as posting but have been lurking around for awhile. You all seem pretty versed on the goings ons with motors as am I to a point. The issue I had this weekend did not invlolve my boat but my motorhome. I figured you all are up on your big block chevy stuff on this site...
  17. Jet Boats
    Where can i find a replacement steering arm for my berk 12jc. The current one is cracked at the bolt hole for the steering rod/cable. I have really had no luck looking for one online, any help would be appreciated.
  18. GN7 On the Dyno
    i installed the t&d's according to the instructions & that did not work. the valve stems are too long. the heads have a raised port & that put the rocker on the outside edge of the valve. i had to (not shim) the assembly in order to get the rocker onto the center of the valve stem. this caused...
1-19 of 31 Results