Performance Boats Forum banner
base
1-18 of 22 Results
  1. Parts for Sale
    New Engine Mount Bracket & Engine Mount Base, BBC Chevy $200.00 PAIR BEST TO SEND MESSAGE OR TEXT ME SIX18-567-180FOUR
  2. GN7 On the Dyno
    First timer installing a supercharger. Install gasket dry, oiled, glued to one side? Thanks
  3. Parts for Sale
    Have a decent Dart single 4 intake glass beaded,little corrosion around water port.4150 base.These cost 450.00 new.250.00 OBO shipped.
  4. V-Drives
    Anyone know who makes these turnbuckle bases? They have a part number stamped on the bottom of 264-17. I called Bergeron and they are going to see if they have any that were take offs. I need two more to take the B-boat up to 10 turnbuckles and I'd like them all to match. Well that is...
  5. Parts for Sale
    This is a very nice 3.2" offset mag drive that has mech tach drive and 2 lockdown tabs to help keep from moving under exstream conditions..i have a mallory supermag111 on it now but other mags may also fit;;you be judge on if your mag fit it or not..i went from rear location to front drive on my...
  6. Parts for Sale
    468 BBC with a 420 base. HP 500 cam trick flow lifters roller rockers Merlin steel heads KE 4.5 exhaust speed pro 9.5/1 pistons Teflon bearings gil 10 qts pan double roller chain air gap intake 850 holler Eddie marine arrestor Teague valve covers all acc. Bravo coupler and bell...
  7. V-Drives
    Got a few requests to make up some 1" Billet Rudder Box with a round base flange. Same features as my square flange but with a 4 1/16" diameter round flange. More info on my PB Parts ad. Thanks, Phil
  8. GN7 On the Dyno
    Getting ready to put the motor back together, what should i set the base timing at ?
  9. Parts for Sale
    I dont know what to call it but my engine fell over and bent the base of the water pump don't know if you can get parts for these or if someone has one thanks for the help
  10. Jet Boats
    Strange thing happened after making at few passes at the lake today - I found a small amount of oil at the base of one of my Holley carbs (front carb) and the few streams of oil had run down the tunnel ram. No puddling, but enough to take notice. I also saw some oil had come out of the valve...
  11. GN7 On the Dyno
    I am looking for someone who can fabricate an aluminum scoop base for me like the one pictured below? Thank you Jim 928-542-7712 [email protected]
  12. Parts for Sale
    I'm looking for a scoop and base plate to fit a pair of 1050 dominators, they are 9.375" center to center, 7.25" diameter. Thank you!
  13. Jet Boats
    just replaced my floor and glassed it in. i have always had problems with my front seats being loose. they are lagged to the floor. because my floor is so low in the boat-i can only lag 1/2 the base because the other 1/2 is over the bottom of my hull. this is the stock setup. my question is can...
  14. GN7 On the Dyno
    I have a chance to get a 98 Vortec 454 for relatively cheap. Would this be a good base for a relatively mild build?
  15. GN7 On the Dyno
    I have not read up on this lately, but can you add power to the mag 375 motor or would you need to pull it and just add something else?
  16. GN7 On the Dyno
    I'm considering purchasing a new aluminum race block. All of the block mfgs offer larger cam bearing base circles as an option. What are the pro's & con's?
  17. Jet Boats
    I would like to barrow any 4150 base carbs 750 or bigger (set of two) for the Tom Papp deal, just for the one day. Would be willing to pay or whatever it woud take to do so. Thanks alot Steve.
  18. GN7 On the Dyno
    ok getting close to starting up my nephews 496 procharged engine blow thru carb setup. his fuel regulator has a 1 to 1 boost reference port (allready hooked up) where should he set his base fuel pressure?
1-18 of 22 Results
Top