Performance Boats Forum banner

bearing

  1. steering post, bearing question

    V-Drives
    just had another stupid question,,,im replacing my steering shaft and gear ,,in the process i decided to replace the sleeve in my steering post,,,,its old really old probably late 60's early 70's and it had what i thought was a brass sleeve so i ordered some oillite brass/bronze sleeves and...
  2. Billett polished casale front bearing covers $15

    Parts for Sale
    I HAVE A FEW of each LEFT THESE SELL FOR $40 BUCKS ELSEWHERE TEXT IS BEST 951 870-69TEN $15 or $23 shipped
  3. [Question] Casale V Drive (TOP BEARING)

    V-Drives
    I have a problem and looking for alternate solutions. I am pulling apart a Casale V Drive to recolor the mid plate and polish or coat the cases. However, when I removed the top bearing cap to remove the bearing there is no grove in the bearing for the puller. It appears whoever had this case...
  4. front cutless bearing keeps moving forwards

    V-Drives
    Hi All Flat bottom 18ft race boat. The front half of the cutless bearing (i.e the bearing in the front of the prop skeg), keeps walking forward out of the skeg. Is this normal? I used a little bit of locktite when installing it - does it need a lot? does it need to be glued in? Is this...
  5. cam bearing

    Jet Boats
    if you put some what lite scratches in cam bearings removing the cam would you replace them .two trips two the lake on them......
  6. WTB Berkeley bearing caps and packing ears

    Parts for Sale
    WTB Berkeley/AT/Dominator front bearing caps and packing ears , please PM with what you have to offer
  7. [SOLD] Wanted. 10* Casale input bearing shaft seal/cap/retainer

    Parts for Sale
    I'm in need of a casale input shaft seal cap/bearing cover. It's the cap or holder that the input shaft slides through on the casale 10* case. Mine seized a bearing and it destroyed the shaft and holder.(Se pics) I have one to replace the one on the race boat but I had to rob it from my other...
  8. Want to buy. Casale bearing cap for input shaft 10*

    V-Drives
    I'm looking to purchase an upper bearing retaining cap for the input shaft for my 10* case split box. My bearing seized on the race boat and it took out the retaining cap. It wasn't pretty. Last lap in a very important points race. Take a look and see what you have laying around. It needs to...
  9. Turbonetics 72mm Ceramic Ball Bearing Turbos

    Parts for Sale
    Pair of Turbonetics T-7268 Top of the line turbos. T 4 flange 72mm compressor .81 Ar exhaust housing. Very quick spooling. Low use. Custom anodized compressor housings. New cost $1550 each, for sale $1250 for the pair. Tulsa, OK 918-269-8084
  10. Torrington Bearing for Cam Waterpump Drive

    GN7 On the Dyno
    What Torrinton bearing do you guys use for controlling cam forward thrust between the timing gear and the back of the cover/ water pump drive? I already have a Cloyes roller timing set with the bearing set up on the backside of the gear. Where does the bearing run on the front side of the gear...
  11. Full Cam Bearing Freeze Plug Misc Cabinet

    Parts for Sale
    Approx 120 sets of cam bearings some pretty rare in the back early hemi Arias fontana coated Dart etc. several sets of good BBC bearings h hx hxn etc. Tons of freeze plugs and galley plugs Rod bushings a few rod bolts and nuts block dowels pipe plugs other misc similar items. Galley plug...
  12. cutlass bearing ??

    V-Drives
    Hey folks, Have a 1959 Biesemeyer that has a 1" prop shaft and Cal-Marine prop struts on it. The cutlass bearings need to be replaced but after looking for bearings on-line they not only have an inside diameter but a choice of outside diameters also. Anyone know what size outside diameter I...
  13. [SOLD] WTB Casale v-drive Bearing cover caps

    Parts for Sale
    need a pair of these and it doesn't matter if it has thew tach drive or not. Building a v-drive and missing a pair of these.. let me know if you have something. they don't need to be Pretty or billet. its a stock case and would look weird if they were fancy ones.. thanks.. Bill. 530-333-1047
  14. [Press Release] D21 Ent and Collins Billet Top Bearing Cap for Tach Drive

    V-Drives
    Top Bearing Cap for Tach Drive Made from beautifully machined 6061-T6 aluminum. This cap is vented and is a direct replacement for your cast top bearing cap with a tach drive. 6 hole bolt pattern. Thanks, Phil 925-323-9093
  15. [Video] How To Videos for strut bearing replacement

    V-Drives
    How To Videos for strut bushing replacement A few videos I made over the weekend..... Here's the first half of project. shows taking everything apart.
  16. Casale Bearing Caps

    V-Drives
    Wanted some "fancy" caps !
  17. Nitriding Depth and Bearing Material

    GN7 On the Dyno
    Callies Compstar BBC 4.25 crank 4340 that has had the rods turned .010 under. Does it need to be renitrided? What is the usual depth of hardness on a factory new crank? I notice a lot of builds with Clevite "H" series bearings for large radius journals. Any other's preferable or equal/ better...
  18. Bearing P/N for Casale Rebuild

    V-Drives
    I decided to pull my v-drive this winter and open it up for a overdue inspection. Got it apart yesterday and actually looks pretty good inside. I think I am going to replace the bearings/seals while it is out. I have been talking to the local bearing supplier and struggling to find a Part...
  19. Options for increasing bearing clearances.

    GN7 On the Dyno
    I would like to hear what options there are, for increasing bearing clearances. In particularly, clearances on a turned down crank! After going thru a long block that i recently picked up and just checking the main and rod clearances with some plastigauge, looks like the they are a little...
  20. Berkeley Shaft & thrust bearing

    Parts for Sale
    Good condition. Not magnetic, so it must be a standard shaft. $125 Located in Valencia, CA PM me here or email [email protected] with your info and I'll call you with mine.
Top