Performance Boats Forum banner

Discussions Showcase Albums Media Media Comments Tags Marketplace

1-19 of 34 Results
  1. V-Drives
    Changing some things around in my C-1000 which I'm sure has been done before in it's 50 year history so that got me thinking. It has 4 bearings in it. Two are 5308CF and the other two are 5308A's. Best I can tell they are all the same size just two are open on one side and the other are closed...
  2. Outdrives
    I have a 1997 Chaparral 2130SS bowrider that I bought from the original owner last summer with about 1000 hours on the 350 Mag and Bravo III. I had it checked over thoroughly by a good mechanic who, by coincidence, recognized the boat when he saw it and confirmed that it had been serviced...
  3. V-Drives
    Where do I get new bearings? What material? 1.5" prop shaft. This is for a hydro. Thank to Rattle Can Lou for the use of his drill. Actually a modified 1" prop shaft. Made my own bit as his was too little. Now I need to replace the shaft bearings and start drilling more holes. Jerry
  4. Tow Vehicles
    Last weekend I replaced all of the wheel bearings on my trailer. It's new boat to me and they made just a little bit of noise when I jacked up the trailer and spun the wheels. I got wondering why the sealed front wheel bearings on my Expedition have 164,000 no maintenance miles on them and how...
  5. Parts for Sale
    Up for sale are 5 sets Top Halves Only Rod Bearings for the 426 Chrysler Hemi from Childs & Albert p/n R4264B std.. these are typically used in the BAE Hemi...$150 for all 5 sets Thanks for looking
  6. Parts for Sale
    Have a full set of Rod Bearings for a BBC in Standard size.. these are Clevite CB-743 HN (Hardened Narrow) I can not use them since im running a .010 crank now.. brand new in the box set for 8 rods.. New @ summit is 111.76 .. sell the set shipped to your door for 87.50 .. located in the...
  7. PB Open Water
    Getting ready to service my trailer bearings. I have the oil bath style with lenses missing. What makes the oil bath vs the wheel grease different other than the lubrication aspect. Can I convert these to Grease and install buddy bearings kits.. Getting ready to ship from the Midwest. Thanks
  8. Parts for Sale
    NEW - King Engine BBC connecting rod bearings; 13 each - CR808XPN001 3 each - CR808XPN All $35 to your door, Cont. US.
  9. GN7 On the Dyno
    Seriously, is this grease ok for Hi-Temp disc brake wheel bearings, or more suited for ball joints?
  10. GN7 On the Dyno
    I've been running a blown alcohol 427 bbc for the last 3 years pretty much problem free. I've ran it pretty hard, upwards usually 8500 rpms and an ops one time to 9500 which cost me 3 broken valve springs. That being said I've now stopped running it as of this last weekend to freshen it up on...
  11. GN7 On the Dyno
    How do you go about tearing apart a used engine to inspect condition? Can I just pop off a main/rod cap and have a look and retorque them to stock specs? What if someone used a different torque number than stock and I set it to stock? Worst case? Best case? Is it even a good idea...
  12. Jet Boats
    I have a jacuzzi yj12... I know, I know "junk, throw it away" but until then got to get a season out of it and the bearings need some lube. Any ideas on how much to use so as not to blow out newly replaced seals?
  13. V-Drives
    My father called this morning. He wants to tow the Sanger up to our place in the Sierras. Lakeport, Clear Lake, Ca to Portola, Ca. Just over 300 miles. The thing that worries me is the bearings. The trailer has never been towed that far. From the carport to the boat ramp, 100 feet away was all...
  14. V-Drives
    What does it take to change the bearings in a 10 degree casale v-drive to the tapered bearings?
  15. Parts for Sale
    1995 1.87:1 Right hand CLE fresh from Eagle One performance in Florida. 100% new gear set $$$$, new 20" drive shaft, new bearings, seals , studs, water pump, ect..... In flawles condition, still in the box from Eagle One. HP rear drain bearing carrier and 1" prop shaft. Flawless 4 hole gear case...
  16. GN7 On the Dyno
    Problems today! I went to try and fire up my 454 motor on the stand today and I have an issue. Let me first say that this is the first time I have been in the bottom end of a big block. To start off, I put a new crank in it and also replaced the main and rod bearings. everything else stayed...
  17. Jet Boats
    Pros? Cons? Who uses them who doesn't and why? This question came up when discussing a stock 460 build for a cruiser.
  18. Outboards
    Hi all on my merc 115 I was trying to figure some stuff out what I think the issue now is bearings, when I put into gear and spin the prop it is real hard to turn was not like that before so is it gears or prop. I would think if it was gears it would grind.?
  19. Parts for Sale
    MADE A FEW EXTRA raw $30.00 each takes 1 1/4" bushing for 1" cav rod, easy to polish , mount holes are not drilled since everyones is different, im anodizing mine blue for my kurtis can cnc water jet anything else you want let me know dale 208 869 0387
1-19 of 34 Results