Performance Boats Forum banner

block

  1. Blown Big Block

    GN7 On the Dyno
    Have a motor build almost done. Going into a 25 ft Eliminator. Should scoot pretty good 572 with 1471 blower and superchiller. Big Brodix heads with new T&T shaft rockers.
  2. WTB/Looking For 4 bolt Main BBC Block.

    Parts for Sale
    Anyone have one laying around? Or even a short block? I’m in the Central Valley of liberal run/maddening California. Thank, Bill.
  3. Early 350 Chevy Block and parts

    Parts for Sale
    A friend ( a retired boat shop owner) has an early 350 Chevy four-bolt main bare block (standard bore) and some related parts for sale. Located in Upland, Calif. He also has some 454 BBC parts available. Call Joe at (626) 664-9224 for information.
  4. Big block chevy engines and parts

    Parts for Sale
    #1 Blown injected on Alcohol - 496 BBC chevy tall deckblock half filled-4.250 valasco crank- oliver billet main caps-groden aluminum rods-ross pistons-total seal gapless rings-isky 802 lift cam-comp cam roller lifters and push rods- stainless steel comp rocker-crane stud girdles-merlin grumpy...
  5. Eng. Parts World product sbc block

    Parts for Sale
    I have a World products aluminum small block chevy block that is virgin. Asking $3500 OBO call or text 714-749-4395
  6. Eng. Parts Worl products Big Block chevy

    Parts for Sale
    I have an aluminum World Products Big Block Chevy block that is virgin. Asking $4000 OBO call or text 714-749-4395
  7. 383 small block Chevy

    GN7 On the Dyno
    This is for a 4x4 and I know there are some very sharp guys in this subject question I have on here. Its not gonna be a race engine. Its gonna be a mild build to run on pump gas. I have a set of fuelie's going on it and should be around 9 to 9.3 to 1 comp. Cam is 220/[email protected] 507lift 111 lobe sep...
  8. Eng. Parts 540 Merlin III MarkIV Block and parts

    Parts for Sale
    Merlin III Mark IV CHEVROLET CLONE BLOCK - 540 CUBIC INCH short deck block – has been ran for less than 500 miles on street– (piston failure) All other parts of the rotating assembly are good and ready for new piston/ring set and put back together. Will sell all short block parts as unit or...
  9. Roller block question

    GN7 On the Dyno
    Hey guys! Anybody know what year Chevy small blocks started going roller? I am on the hunt for a roller block for a build I will be doing for a 4x4
  10. [SOLD] 500 inch spread port big block chevy

    Parts for Sale
    I have everything except for rods and pistons to assemble a 500 inch bbc, there are some very high end parts that have not been run since freshening up, parts list as follows Bowie block, 4.600 bore, filled to the water pump, bushed lifter bores Bryant 3.75 stroke crank jesel belt drive gm...
  11. PRICE SLASHED AGAIN Extreme Duty Turbo Headers Small Block Chevy

    Parts for Sale
    Dirt Cheap Price For These headers. Heavy wall 304 stainless turbo headers by Shearer Fabrications. 3/8" flanges and 1/2" threaded T6 turbo mounts 1 7/8 tubes. They are new. Engine was started and idled. These are 3X the quality of stainless works and ebay headers dont even come close. They...
  12. Small Block Chevy Twin Turbo System Parts

    Parts for Sale
    Turbos and Wastegates SOLD Headers $2,200 Procharger valve $400 Wilson elbow and Accufab 90mm TB with TPS $300 Best of Everything! No E-bay Components here. No run time, idle time only. 2 Inch 304 stainless turbo headers by Shearer Fabrication. 3/8 flange 1.600 x 1.860 ports. They are a work...
  13. WANT TO BUY SMALL BLOCK V-drive oil pan

    Parts for Sale
    Want to buy a small block Chevrolet V-drive oil pan. Thanks. David
  14. Want to trade big block chevrolet v-drive oil pan for small v-drive oil pan

    Parts for Sale
    Big Block V-drive oil pan for sale $250 plus shipping. Located near Fresno Ca. For Sale. V-drive oil pan. Pan is 7.5” deep. No repairs or damage. I don’t know how many quarts of oil it holds. I have the pickup and windage tray to go along with the pan. Also looking for small block...
  15. 427 tall block

    Parts for Sale
    nice 427 tall block casting # 340220 4 bolt main standard bore been sitting 40 years . $750.00 plus shipping
  16. Engine looking for a good gen 4 454 block

    Parts for Sale
    I do not need it any more, found a complete engine carb to oil pan.
  17. [SOLD] BBC donovan 9.8 deck fresh block, pistons, pins, rings, cvs belt drive, pan and pump

    Parts for Sale
    BBC donovan 9.8 deck fresh block, pan and pump Donovan block is fully polished, freshly honed 4.5 bore , fresh .904 lifter bores and oringed at kuntz and co.- block has been run very little in a show type boat with a carbed NA application a very long time ago and has been in storage for 20...
  18. Looking for long block for blown motor build

    Parts for Sale
    If anyone has something sitting in their shop let me know..BBC Thanks, Matt
  19. $10,500 or Trade 1,500 HP Twin Turbo 385 Small Block Chevy

    Parts for Sale
    Would trade for a street rod, muscle car RUNNING the wife and I can drive around Florida. This engine is fresh. Started not ran. Complete Engine And Turbo System minus intake manifold fuel and ignition system $10,500 Dry Sump, Gear Drive, Shaft Rockers, Billet Caps, Pac Springs, Straub Cam...
  20. WTB - BBC Mock-Up/Composite Block

    Parts for Sale
    Looking to buy a Big Block Chevy Mock-Up/Composite block, preferably in the Southern California area. Russ, PM or Five6Two Eight58SixNineTwo6
Top