Performance Boats Forum banner

combo

  1. Parts for Sale
    Sanger/Jones mechanical tach and Vertex mag complete with cable Mag should be gone through, I took it out of my boat in 2007, was purchased brand new by me with 10deg advance see model # from box $600, located in Upland
  2. GN7 On the Dyno
    Who is running a 565 bbc in there jet boat ? What are some of your combo's Been gathering parts to build new engine parts I have dart block afr 357 CNC heads 10.5 to 1 compression ( pump gas ) single plane super victor intake 1050 dominator i think I'm headed in the right direction ...
  3. GN7 On the Dyno
    I'm going to try boat racing. Never have before, only 4 wheel racing. I have 17'6" rear mount, Vdrive boat with a 383SBC. 22% in Vdrive. The engine was originally street/strip car engine. It's old style build, machined down 400 cast crank, 400 rods, shotpeened with ARP rodbolts, SpeedPro flat...
  4. GN7 On the Dyno
    I have a std bore 454 short block from gm, I got it second hand from another boat. 30 cc dome pistons (gm 3963550), mismatched but both rectangle port closed chamber heads. Machine shop says the cylinder walls will clean up with only a hone and cross hatch. Over transom headers currently, could...
  5. Tow Vehicles, Cars and Parts
    1993 T-600 Toterhome. Coversion done by United Specialties in 06. Has a 450 hp 60 series Detroit and Eaton 9 speed. Has air ride seats and cruise control. Truck runs great and has plenty of power to haul this trailer even with three boats and gear inside. New front tires and batteries. Has a...
  6. Jet Boats
    A impeller boat is a 20 ft mini day cruiser 468BBC 9.5-10:1 compression large oval port heads high volume fuel pump regulated cam is Intake Duration at 050 inch Lift 261 Exhaust Duration at 050 inch Lift 261 Duration at 050 inch Lift 261 int./261 exh. Advertised Intake Duration 312...
  7. GN7 On the Dyno
    Well, here it is. Just a couple little finishing touches and it will be ready for the Dyno on Friday morning. Hopefully it does not spill its guts:shock:.
  8. V-Drives
    I have a crazy idea that most would say, "what are you thinking". With that said, bare with me and laugh your @$$ off at my expense. I have a 1988 20' gutted bay liner that was given to me for free. It came with a i/o. I'm going to reshape parts of the top section/add a newer style malibu...
  9. Jet Boats
    Not the GAY Orange Daytona > but the cool, classic 1983 21' Daytona. BBC, NA, Competitive trailer Minus fuel (50 gallons) Any ideas? Thanks
  10. GN7 On the Dyno
    I am looking for some advice on a wet sump pan pump combo. I have a dry sump system that I don't need and would like to go with the simplicity of a wet sump. It is a gen6 509 with low 0.6" lift that will maybe see the upper 5000 rpm range. It should make around 600 hp. In that rpm range. I...
  11. V-Drives
    Any one know what it takes to mate a Lenco clutch and tranny? I got one of each and don't see how they get hooked together.
  12. V-Drives
    Frick'in HUGE nice conversation piece while sippin in the garage!!!!!!!!!!!
  13. Jet Boats
    Looking for a nice Cheyenne hull and trailer for sale. Prefer a dolly type trailer to put in our enclosed trailer. Any help would be appreciated. Thanks, Larry
  14. V-Drives
    Testing the K-50 Coldfire - YouTube N I C E !!!!!!
  15. GN7 On the Dyno
    I run a 565/14-71 combo on pump gas in my jet boat and currious if anyone else runs power valves or what others run? Two 1250 dominators for carbs with 4.5 power valves in both primaries and secondaries, 94 and 96 for jets. The plugs are autolight ar3932 and are always black and sooty looking...
  16. Trailers and Trailer Parts
    2004 Shadow Boat / PWC combination custom trailer. This trailer was built by Shadow trailers in Cypress, CA. Check out shadowtrailers.com. My trailer is featured on the website. Look under Boat PWC combo trailers. It's number 3. Was built to hold an 18' boat and two skis, full size or stand...
  17. Political Rhetoric
    Donald Trump | Allen West | Allen West not closed to idea of being Donald Trump's VP | The Daily Caller - Breaking News, Opinion, Research, and Entertainment "Florida Congressman and Tea Party favorite Allen West isn’t opposed to the idea of joining possible presidential contender Donald...
  18. GN7 On the Dyno
    Got in an interesting conversation today with a guy about which makes a faster boat, This guy tells me "torque" is what you want and I kind of disagreed with him. He says torque is what pulls you up to speed and horsepower doesn't count. So I was thinking... torque is optimum for heavy vehicles...
  19. PB Open Water
    There is a NEW ice cream shop across from where I work at the Valencia Town Center in Valencia called SHAVE iT and I have hired them on to supply the ice cream/ shaved ice for our annual 4th of July tenant event next week. I had to come up w/ an ice cream combo in Blue and the kids at the shop...
  20. V-Drives
    Hey guys my bro has a sanger flatty, 427bbc about 425hp casale 10deg 1:22 gears, and stelling 11 1/2x15 prop is it geared too high for his hp, what would guys recomend for gears? 9z or 12z or 15z or 18z would u also change the prop to run with the set up you would recomend? :)devilThanx for...
Top