Search Results for ‘crack’

Any recommendations for repairing these cracks in the floor? Was thinking either a penetrating epoxy or a flexible epoxy. They seem to be just in the top layer of resin. Ripping up the carpet and planning on painting with an enamel paint (bilgekote) and don’t want them coming through eventually...

So I was under my cole v-drive, pulling the prop, and noticed a 3-4" crack running from the prop shaft through hull hole, back towards the strut. The hull is a bout 3/4 - 7/8" thick. How dose one fix this? Sorry no pics

Hi, Just wanted to know if a Crack in no#2 Main saddle is at all repairable it is straight across the oil passage and goes down the saddle almost 1/4inch, It is a bowtie 184 block, 4 bolt splayed caps, I spun a rod bearing and there was obviously excessive heat, Crank is no good. Just wanted to...

There is repair question here but first. Hello all, first time here. I am looking at a boat (Obviously)(23' Omega) from a few posts i've read not the most loved boat maker apparently. I'm negotiating now for what i think is a fair price, anyway On both sides from just under the top of the...

I found a three foot hair line crack on the hull of my sanger super jet in about the middle of the boat right along a chime...... the boat needed a new floor when i got this thing... i replaced the floor and was wondering if any of you have had the same problem and how you fix this or do i find...

background story first: when i first got my boat i pulled it off the trailer and found that the seats were through drilled from the keel side in and bolts were used to hold them down. when i finally got on the water i had quite a bit of water coming from the front to the rear and expected it...

I am having a hard time deciding if this is a crack or not. My first thought is that it is a crack. The more I look at it I think it may be a grind mark from when the intake was set. This is a 21' Daytona with a full set back pump. I tried using a .006 feeler gauge to determine if it is a...

Im just trying to get advice and make sure the plan I have is good to go before I order my materials. I will be using Epoxy resin, is two layers of 17oz biaxial on the stringers with a layer of 6oz "S" glass on top good enough? Also.. can I just use the 17oz biaxial or do I need to alternate...

how does this look to everybody please chime in does it look normal serious is it structural opinions appreciated thank you

I have a keel crack on my 21' Eliminator Daycruiser that is leaking. What is the best way to fix this? It seems to me that the prescription would be a few layers of 3" fiberglass tape over the cracked area and then maybe Keelguard on the outside of the boat. I know that it will look a little...

My question is I noticed these crack on the hull in the pad area. I am quite positive I didn't hit anything manufacture says it is due to impact. There is no signs impact however is it possible you can do this damage without knowing? Boat is 2007 bass boat with 150hp Area where it is cracked...

Hi all, thought i would post up another thread. I have a crack issue on the top of the shell, right on the top edge of the hull where it begins to peak, then heads down on the inside. Was wondering if anyone has any advice how to repair. I can V it out no problem, and fill with fibreglass...

My pump housing developed a crack! Will upgrade to 16 bolt dominator. Eventually I will have replaced every part in my boat. :duh:

I have a crack that starts from the fin and runs up to my intake grate. Both sides of the fin are cracked.:mad: Im sure this is not good and need to know if it can just be welded up or do I need a new intake? It has been there for a few seasons and the boat is a spectra 20 day cruiser with...

When I had my pump out for a replacement I noticed that the bolt holes in the transom "box" had some cracks in them, what looked like someone had REALLY cranked down hard on the bolts and just smashed the crap out of the fiberglass itself. My question is whats the best way to fix this situation...

Ok just redone my floor in my 1977 sanger and now I have a nasty crack on the chine right under passenger seat. Fixxed temp. over 4th weekend to get me going now have a spot just in front of repaired spot.WTF????

2 months ago Cheetah was on the same level as commander.. If you said anything possitive about em, it was bounced to Grey Water. By reading the boards today their the new DCB. :D And you can buy one for 35K, For an extra 200 bucks it's "loaded." (being sarcastic of course.. I think the...

http://www.usatoday.com/news/washington/2009-04-29-crack-laws-obama_N.htm?loc=interstitialskip

I scraped and sanded 3 old paint jobs off the deck of my TX yesterday and discovered this lovely stress crack:). It was visible with the paint over it, much obviously much less. What's the best way to ensure that it won't show up through my next paint job?