Performance Boats Forum banner

Discussions Showcase Albums Media Media Comments Tags Marketplace

1-20 of 52 Results
  1. Parts for Sale
  2. V-Drives
    Getting ready to fab my drop in strut mount and plan the install. Would really appreciate some pics and ideas for a mount and brace. One question I have is how much of the top of the strut do you guys see as enough above the inside of the boat? I planned on 1-1/2" but the hull turned out to be a...
  3. Parts for Sale
    I am selling a pair of 454, 420hp. One was rebuilt this year the other two years ago. they also have imco exhaust. Looking to 8000 for the pair .
  4. Parts for Sale
    flat bottom 1in drop thru used with mount 200.00 plus ride 928 566 4104
  5. GN7 On the Dyno
    Anyone that does a lot of bench testing.. can you give me some kind of ballpark idea how much CFM you lose when a Holley 750/Single plane like a Vic Jr. is bolted up to an AFR 185cc runner head that flows 295CFM @ .550 lift? Need some numbers to plug into a program to see if I am sort of close...
  6. Parts for Sale
  7. Parts for Sale
    New from mold old school tear drop scoop $200 shipped PULLED FROM MOLD TODAY $200 shipped $175 local
  8. Jet Boats
    I'm obviously a bit of a newbie to this neck of the woods so allow me to first say: Hello my name is Scott and just like the rest of you folks I have a problem...,, its an addicion I've fought my entire life.. I'm a hotrod project junky... There you go I've admitted that I have a problem...
  9. Parts for Sale
    Less than 20 hours, top pin pistons, ready to ship. Stock electronics. Drop on $6500.00 Drop on with Cowl and Chaps and Pan $7k This is an un molested block, no welds, clean as they come. :thumb: Contact Scott @ 530-712-5211
  10. Other Stuff for Sale
    Selling these what you see what you get complete <br> I can't remember if there 2 or 3 in drop???<br> Pads and rotors are good <br> 8 lug<br> ready to bolt on<br> $400 plus the ride<br> Call or text<br> <a href="tel:7026309625">7026309625</a><br> thx for looking also they fit early 90,s and down
  11. Parts for Sale
    ****1996 Mercruiser 502 EFI Complete drop-in motor with approx 300 hours - $5,500 I'm just cleaning out the garage - Ran GREAT when I pulled it out of my 25' Power Play - This is a COMPLETE DROP-IN motor set up for a Bravo one drive - only thing you'd need is the front motor mounts and exhaust...
  12. Parts for Sale
    Lowering Shackles for a 1500 Silverado/Sierra. These will fit any 1500 model from 2007 to current. On my extended cab 6' bed 2011 truck these shackles lowered the rear 2". Please PM with any questions or to buy them. $100 obo, come get 'em. -nick
  13. Jet Boats
    I'm at a crossroads with my family's 75 Wriedt Maverick 18' jet boat. It's been in our family since day 1 when my Dad bought it off the lot in Norwalk, CA. The jet was rebuilt about 15 years ago, but the engine is '75 original. It still runs but blows a lot of oil out of the breathers and has...
  14. GN7 On the Dyno
    Boat was bought last year, Tom from JBP's low budget build that was a work in progress in here. I only ran it twice last year for a few minutes each time, and it had an oil leak at the base of the dist. both times. I have a 454 BBC that had the stock HEI dist. that I switched out to an MSD...
  15. Trailers and Trailer Parts
    10" Friedl drop hitch. 7500lbs capacity. 750 lb tongue weight. $100. Can bring it to irvine lake this weekend. Buyer pays shipping
  16. Parts for Sale
    American Turbine Droop Snoot with Manual Diverter / changable nozzle inserets. $550.00 417-858-8616 [email protected]
  17. Jet Boats
    In the pic , the shoe is about 5/16 above the keel.
1-20 of 52 Results