Performance Boats Forum banner
end
1-15 of 92 Results
  1. Parts for Sale
    Smith Brothers Push Rods: They are over $32 each new. S.B. will shorten them for $5 each. Heavy wall 7/16 double taper 5/16 ball. There are ten 9.778" long one brand new $80, nine 9.860" long $72 and eight 8.980" long $64. Trend performance: Heavy wall 1 piece 7/16 double taper push rods...
  2. Jet Boats
    Anyone know the diameter of the typical steering cable end (pump side)? It's the stainless rod that bolts to the nozzle. Thx
  3. V-Drives
    NEW DATE - End of summer v-drive get-together ​What: Dog and Andy's End of Summer V-Drive Get-Together When: Saturday, October 7 Where: Windmill Cove
  4. PB Open Water
    I am replacing the throttle cable on my 21 Daytona and I can't seem to locate a cable end that connects to the Nicson gas pedal. The old adapter has a 10/32 female thread on one end and a 5/16" hole in the other. Through all my internet research, I haven't been able to find a replacement. I'm...
  5. Parts for Sale
    All parts prices are + shipping. Please PM me if interested, post questions on this thread. Here we go; 1) Pair of 3" tall S/S flame arrestors. Fit 4150 (5-1/8" dia.)...........$80.00 SOLD 2) Pair of 2" tall polished aluminum carb spacers. Fit 4150 size carb flanges..............$50.00 3)...
  6. West Coast - North
    Skagen Boats End of Summer Bash 2016 Sep 9,10,11 Just 5 days away Mardon Resort Eastern Wa:)devil
  7. V-Drives
    Winter project is coming along
  8. Jet Boats
    I have a 1978 Bubbledeck. It has bbc and berkeley pump with jack plate and place diverter. Boat gets out of the whole quickly but only tops out at 65 mph. How do I increase top speed without losing hole punch?
  9. V-Drives
    Yes I am still driving the K-711, we have just taking a few races off to get it dialed in. Rather then rush it and not having our shit running right, Pat is taking time and busting his ass to get it right
  10. V-Drives
    Talking with a few guys about going to lake berryessa one more time this year. Will be at puta creek
  11. Off the Water
    OK SO here we go again - we are going to be having a BOP - "Big Ol' Party" out at the homestead again to celebrate the END OF SUMMER and to just have a reason to get together and share some fun on dry land. Party Place: WILTON , CA (nearest to Galt area off Hwy 99 and Hwy 104) Party Date...
  12. Jet Boats
    I dont even know where to start.....I had to replace the gas tank in my 74 Tahiti (455) due to rust on the bottom of the original tank. Once replaced I took her out for a test run and she started bogging down at low rpm. Almost seemed like some carb adjustment or timing. (Which was...
  13. Parts for Sale
    1 set of 12 degree pro filer ported by steve schmdit ti valves jesel rockers manley spring profiler tunnel ram fresh made big hp on a 632.916-968-4403
  14. Parts for Sale
    Probably junk to most guys on here but its worth a shot... Small oval port iron heads complete with valves/springs/rockers/hardware. Worked fine when removed, some surface rust and slightly oily but otherwise runnable - $200 Matching iron manifold with heat shield - $100 Used loader - $25
  15. GN7 On the Dyno
    This is stuff I think about...who desinged and knew the proper angel, when useing a open-end wench They allways seem to fit..
1-15 of 92 Results
Top