I'm thinking about putting a k motor in my biesemeyer. Would the motor placement be different from the norm. I currently am running a 600hp bbc. Any advice would be greatly appreciated. Thanks Jeff

... starting a project to replace the toe board and the side boards in my Bezer. First, the toe board is still in good shape but the access hole is huge and it's not glassed in all the way around. I planned on cutting it out and replacing it but was wondering if I could leave it there and glass...

This weekend she ran 119 bumping the rev limiter(6000) 1100 or so HP 1.35 gears BBlades bravo 32p.I left the trim in this photo were it was during this run, looks very close to nutral or maybe a hair tucked in. Boat was very planted, in my old 21 Daytona wacker, I would air it out with plenty of...

Hey guys, my name is Shan. I'm a 27 year old young buck who likes to go fast and I just blew my cash on a big blue 27' tunnel hull but I can't find anything about Powercat making it nor Hawaiian making it. Can any of you give me details on who made it or who to contact about finding out more...

Waste of time, not worth the irritation for me to be straight forward with my issue. I do appreciate those that tried to give me honest advice.

1973 Biesemeyer Flat Bottom V-Drive K Class This is what I do for fun...I look at Craigslist ad's and then tell people they are wrong...tell me what's wrong with this ad...and then contact him through the reply button and tell him.. This one really gets to me...because what his claim is would...

Good evening to all. Got to run the hallet today. To bring you back up to speed; 460Ford, twin Ray jays, now with old style Banks inner cooler, and waste gates with 10lb springs. Custom carb has been referenced, 950cfm, 79 in prime with PV, 90 in secondary's with plug. From 800 rpm to 5,000 the...

Anyone see a problem with running a b279 on my 2013 duramax? The b1441 is what Baldwin makes for the duramax but I need filters for my boat too. Currently have a b1428 on the boat because I couldn't get a 279 so I figure if I can run them on both my truck and boat i'd buy a case but just...

Specifically 1981 Corvette differentials. I got the rear out of my Vette and could use some feedback about Stub axles and Center Pin wear. Thanks

Looking for your advice Putting together a Mercury 2.5 liter drag motor on my 19 DCB/Daytona like to run 9's We will be spinning it 10,000-10,500 RPM with NOS/ Meth I have a pair of bosch fuel pumps , I'am thinking about running 2 pumps in parallel each with a one way check valve in the...

My friend bought a turnkey 454 Gen V block to put in his jet, took the electronics off, put a 80's model factory intake (spread bore), he used factory intake gasket (#90665) I was informed that we may have an issue with water not traveling throughout the block and heads correctly? heating issue...

Ok I just bought my first GF grill. What the hell are the normal cooking temps and times for the basic foods for this thing...??? Didnt even come with a dummy guide or cheater...??? Like a basic chicken breast. What the temp and time ?? Thanks in advance...

02 Escalade mirrors have an auto deploy feature can they be manually folded with out gear/motor damage ? Tom

who is the number one rogers specialist? knows the hulls inside and out, knows what makes them perform best. what kind of power and pump placement. all the things needed to take an ordinary backyard find and turn it into a real gem again on the water. thats the guy i am looking for. any one...

had a drip from the pump, so I changed the impeller and housing o rings. Well it's dripping from the weep slot in the drive housing. Appears to be a couple seals in it, Who sells the seals and anything else I should look at?

The title says Byers as you can see its not! This boat belongs to a good friend from Twin Falls, this boat previously belonged to his cousin in So-Cal, its been in the family for about 35 years, no ID on hull so think it must be mid-60's. Thanks for looking!! Spudz

Finally going to do it myself, and rounding up some materials. How deep/long staples should I use? One layer of felt? More?

Need a little help with this picture. I have a workmate that races a Superbike. He also looks a bit like Eddie Munster. What I would like to see is Eddie Munsters head on top of of either the sheep or the sheppard and then inserted into a Superbike race. I know this place is full of photoshop...

I have a Kitchen Aid supurba 42 built in refrigerator. It's a 1999 model that came with my house. Alder wood paneling. It runs all the time since I bought the house so I vacuumed all the dust off of the coil unit that sits up above the fridge. That made it run better but It was nasty... The...

I have an old laptop with Windows XP that no worky no mo. (That's not my issue) My question is: Can I use the Windows XP OS disk from the laptop and install XP on the Vista machine? I know I would probably have to re-format the HD on the Vista machine to dump Vista. Anyone have any experience...