Performance Boats Forum banner
hallcraft
1-19 of 19 Results
  1. Parts for Sale
    +Hallcraft V-Drive, paralell Shaft 1x1 Ratio all new bearings and seals, with drive mount drive shaft and couplings $500 + shipping from 89410
  2. Parts for Sale
    Need to replace mine as it is damaged... evidently they don't make the hex ones anymore. Thanks!
  3. V-Drives
    so here i am asking the stupid question why do you prefer the casale box over the hall craft aside from the straight cut gears? i understand the older hall craft boxes are not made for high horsepower i have the smooth hall craft model that someone took the time to install a whirl-away so I'm...
  4. V-Drives
    I've recently put together a Hallcraft drive (the one iwht the plate in the middle of it). New bearings and seals, shimmed the gears, filled with oil. I started the motor for the first time today and noticed that the drive is fairly loud. Is this normal? I've never owned a boat like this before...
  5. Parts for Sale
    I have a set of gears for hallcraft v-drive 12% over exc. Contd. $225.00,you can text me or call me at 727-389-3275
  6. V-Drives
    I have the drive out of my Howard sitting on my bench and want to start tearing into it. Has anyone rebuilt one of these or have any resources that would help me? Any type of manual or directions on the proper order to tear down, torque specs, bearings, etc... would be extremely helpful! I have...
  7. Parts for Sale
    Looking For 19 percent ( or close ) hall craft gears ? It is a 10 degree and has 1 1/2" 10 spline I have a chipped tooth in the top gear.
  8. Parts for Sale
    REALLY NICE SET OF TEMP GAGES THAT BOLT ON THE FRONT OF YOUR HEADS $50 shipped to your door
  9. Parts for Sale
    1 set of 29s and 1 set of 38s for 10 degree hall craft v-drive......$200.00 a set...located in Lakewood California call Dave 562-965-3233
  10. Parts for Sale
    $ 75 obo ebd
  11. Jim Wilkes
    The 1977 Riviera I am restoring has a Hallcraft Rudder assembly. The boat sat for many years and the Rudder has a lot of slop in it. I disassembled everything, cleaned it up & replated the Rudder. There was no shaft seals installed. The Grease Fitting on the Shaft Log is good. Do I just pack the...
  12. Parts for Sale
    Looking to swap the 19s in my menkens 10 degree box to something a little lower. Want a little faster outa the hole. Boats a Hondo sprint with a 11.5 x15 prop and a 427 solid roller motor.
  13. V-Drives
    Just picked up a flatty with a Hallcraft V-drive just wandering if these drives are any good and how they hold up, the up's on down's of them Thanks
  14. Parts for Sale
    WOULD LIKE TO SELL HALLCRAFT WITH 12 GEARS $450.00 OBO i can take to cal. at the end of next month so shipping would be free. will post pics later
  15. V-Drives
    I need 2 Hallcraft 10* aluminum shaft logs. I am restoring a 1955 Joe Mandella twin prop-twin rudder speed ski boat. I sent the shaft logs to be polished, they were lost. HARLAN ORRIN
  16. Parts for Sale
    Looking for 19,23,or 26. Let me know what u have I have 12 and 15 for trade. Thanks Dave.562-965-3233
  17. Parts for Sale
    eBay
  18. V-Drives
    Have A Hall-Craft V-drive in this Wriedt that im putting together with runninbroke and have a question. There are 2 ports on the gear box labled WATER... one on the front and one on the rear. Which is intake and which is out??? Also, I have heard it is not neccesary to run water, is this...
  19. V-Drives
    IS there a way to tell whether a hallcraft is 10 or 12 degree ie is there a number cast somewhere on the casing?
1-19 of 19 Results
Top