Performance Boats Forum banner

Discussions Showcase Albums Media Media Comments Tags Marketplace

1-15 of 75 Results
  1. Jet Boats
    I just got a 91 Advantage open bow 20.5. With it sitting on the trailer, the steering wheel can be turned from stop to stop with my little finger. Put it in the water and it like wrestling a bear. The pump is an American Turbine ATJ with trim. I ask because my last boat (78 Southwind) would...
  2. Delta Lunch Bunch ( dlb )
    It's only 157 days to March 17, 2017 Wear something green.:D 1. NP & Shorty < (think leprechaun) + 2 2. Chestah Cheetah + Scotty Good Eye 3. Lake P.A.L. and Mrs 4. F14 +1 5. RogerThat99 +1
  3. Boats for Sale
    Time to sell my beautiful ski deck Biesemeyer Floors and hardware are very nice. Hardware is anodized Gold and black. Complete boat is put together with stainless ARP fasteners. Polished 10 degree v-drive with tapered bearings. Solid driveline, new prop shaft A22, and new stainless rudder box...
  4. Jet Boats
    I bought this 1976 Spectra 20 from a guy up in Reno NV last year. In my excitement of finally buying a nice boat I hauled ass back to Vegas. My girlfriend and I took it to the river for the first run and it ran flawless. We took it out for a few more short trips out on Lake Mead, and then...
  5. V-Drives
    Does anybody sell the hard lines for a magnaflow water pump? Thanks.
  6. Jet Boats
    I just installed an Aeromotive electric fuel pump for mySJ. Pump is rated for over a 1000 HP. It's on a 505 BBC with a 1050 Proformcarb (1/2" line). I have it regulated down to 8 PSI. I think the motormakes around 600 to 630 HP. Coming in to the dock, I ran it 4k for a few minsand went to around...
  7. Jet Boats
    What gives? Can cruise around all day with no issue but I romp down on it a few seconds and then there's a ton of water in the floor. It's not the headers... I turned the water off to verify. Any clue?
  8. V-Drives
    I was wondering if it is OK to use Aluminum line for hardlines rather than stainless? In particular for water lines. I want to do a few of our boats in all hardline, but I'd like to practice on the non-showy boats using cheaper and easier materials. The aluminum line is "not recommended for...
  9. Jet Boats
    Broke the driveshaft in the lights. 130+ MPH. God was looking out for Dillon. It sat down and drifted off to the right. Ran to Bergeron and bought a replacement PTO. Had a replacement front yoke. Thanks for everyone that came by and offered help. Thanks for the pics Gary Payne. Seems theres...
  10. GN7 On the Dyno
    I have a stock 1994 454 carb motor. it is almost impossible to start while on the water. once it is running, it runs good. if I shut it down it will start right up. if I let it sit for more than 15 minutes I have to hold the throttle wide open till it fires. it acts like its flooded. it's done...
  11. Boats for Sale
    '06 Conquest Boss Cat Hard Deck 525 $65K OBO My new Top Cat II is out of the mold. Need to sell. Mercury 525, dual ram, full hydraulic steering, Serviced at the beginning of each season and fluids changed every 20 hours. Nice stereo & DVD in the cuddy. Lots of extras, sea strainer, after...
  12. Jet Boats
    Hey all, Been away for a while and finally getting back into it. Anyway I remember some guys posting on the old hb forum about replacing all their cooling hoses with hard lines. Anyone here do this, or remember what they used?
  13. Parts for Sale
    These came with my blower PO told me they wrap around and down the blower and block motor was a 540 with BDS 8-71 and 2 side mounted 850 Holleys. there is a fuel pressure gauge bung welded in line. I scratched my head on them next to the blower for about 1 min. trying to figure it out but...
1-15 of 75 Results
Top