Performance Boats Forum banner
21-40 of 69 Results
  1. GN7 On the Dyno
    I want to hard line my carb to the regulator and noticed these AN to hard line adapters; Are these fittings reliable for what I am trying to do?
  2. V-Drives
    I understand that you need power to keep the front end up on a v-drive but there must me more to it that just a lot of power. Like ridinig a wheelie if your accelerating sooner or later your going to run out of power and the front end is coming down. I quess my question is that if you have...
  3. PB Open Water
    I have a 87 Sea Ray. It use to have a 4.3L chevy V6 in it, but now I put a high output 350 in it. I put edelbrock performer rpm cam and intake in it. I have the edelbrock marine carb with mallory marine ignition. I have a holly electric fuel pump also. It starts fine when the engine is cold...
  4. PB Open Water
    Hopefully this jackass will become someones prison bitch
  5. Parts for Sale
    fuel Hard lines 4500 series dual carbs $ 70.00 located 91344 ca
  6. Jet Boats
    My old throttle is looking kind of ragged...the shifter feels sloppy, and then I saw this: Thought it might be a nice upgrade! Just wondering how hard the install is.
  7. V-Drives
    Seen most of the pics that have been posted on here of this boat I think. Anybody have any more shots of it? Hell I dunno, just can't stop staring at it...gorgeous deal.
  8. Jet Boats
    I have heard this complaint from others too, with droop,p/d, higher it's set the harder too steer.Is there anything I can do over the winter to fix this . I want to add a wedge,thats not gonna help.thanks for any idea's/experience:yes:
  9. Jet Boats
    After almost sinking my last boat due to a rather large hole that I acquired from far exceeding the limits of my last hull, I have finally got one that runs good. I have only had this hull for a little over a month (after I got it rigged up) and it took some time to get used to how it handles...
  10. Parts for Sale
    Dominator 4500 carb stainlees steel blower hard lines & fuel rail DOMINATOR 4500 CARB BLOWER STAINLEES STEEL HARD LINES & FUEL RAIL. YOUR CARBS WOULD HAVE TO BE ON 8 3/4 CENTERS FOR THIS SET UP TO WORK OR RE DRILL THE FUEL RAIL. $95.00 PLUS SHIPPING. I can take pay/pay also.
  11. Jet Boats
    I want to do stainless steel hardlines from my fuel pressure regulator to my 6109 carbs. Does anyone know who does this type of fabrication work in the So Cal area?
  12. Outboards
    Hard To Port !!! Is she hard to port? She's hard over sir.
  13. V-Drives
    Any other ford fe guys out here with one??. Thanks in advance for look'n. jeff
  14. Jet Boats
    thought you guys might get a chuckle out of this pjkLf_X88WM&vq=medium
  15. GN7 On the Dyno
    540 cu in 14-71 blower with bird catcher on gas in jet boat. have primer on it and starts good when cold but after you run it and get it hot and cut off with fuel shut off on top of pump the only way to start is to open butter flies and then when it fires it takes off. thanks
  16. Jet Boats Thoughts?
  17. GN7 On the Dyno
    Can anyone give me any ideas why my boat does not want to start after sitting over night. It's a 454, 177 blower, holley, mechanical pump, timing locked at 34, msd ignition. It will crank like a mofo but nothing with out starter fluid in the morning. Starts and runs like a champ all
  18. West Coast - South
    It started out great Sunday AM. Got to the lake with Kyle and cruised all around till around 9am when we saw Keith and his crew at the docks. From the vids everything looked and sounded fine As soon as we get to the no wake bouy in the back I hear a scary sound. At first we thought it may be...
  19. PB Open Water
    well my old dell after 8 years, the hard drive died on me:mad:. question what do i have to do to change it? or should i just buy a new tower. how hard is it to change out the hard drive?
  20. Jet Boats
    Got a carburated 502 chev with an enclosed engine compartment that is a bitch to start after I run it. If I start it right after I shut it off, it does fine. But if I sit on the beach for more then 5 minutes, It takes a whole lot of cranking and then full throttle to get it going. I changed...
21-40 of 69 Results