Performance Boats Forum banner
hardware
1-20 of 59 Results
  1. Parts for Sale
    Removed off 71 Howard GN, real good condition...I know the boat has sat in storage 20 years of its life so chrome is good. $350.00 obo plus ride. 951-377-2775
  2. Parts for Sale
    Interested in used Cavitation Plate Hardware. Particularly, looking for a matched set of eight (8) 3/8" X 1 3/4" to 2" stainless eye levers and 3/8 "stainless pin and e-clips. Thanks Scott
  3. Parts for Sale
    Want to buy cavitation plate hardware for V-bottom boat except for the plates. Need cross shaft(s) machined for the short levers, turnbuckles, short lever arms, actuation lever and through transom seals. Either one long shaft with staggered turnbuckles or two angled shafts and same length...
  4. V-Drives
    Have a couple of question new set up on Biesemeyer. My hull has recesses for 1/4" plates (blast and calvplate), should I use 1/4" alunimium or3/16" stainless for the calvplates, and should I use 1/4" or 3/19" stainless for the blast plate? My thought is the slight step from the hull to plates...
  5. Parts for Sale
    Caselli Dual Pedal- $150 7/8" Pillow Blocks, structurally sound, but have cosmetic damage to be worked out, $40 for all 4 7/8" Control Arm, 5 1/4"- $35 Plate Pads- $25 for all Pins- $10 Hallcraft Steering Pulleys- $100 Quadrant, 1"- $50 3/4 by 32" steering shaft with gear, 3 hole wheel...
  6. Parts for Sale
    rudder stuffing box, prop seal for 1'' shaft and cav rod seal. New still in box, never used. $450 for all
  7. Parts for Sale
    I have Brand new Cav Plate Hardware from 70's All in great condition Hexagon Bar is 65" wide made of stainless Turnbuckles are stainless Rest of Hardware is chrome over Brass or Bronze took these out of packages from pics been storage since 70's $450 Call Tim (508)902-8528
  8. Parts for Sale
    SILVER COATED PLATE ALL HARDWARE PICTURED WILL NOT SEPERATE PARTS PICTURED WILL SHIP ALL THIS I HAVE THE ROD THAT GOES FROM THE TRANSOM TO THE T-HANDLE OR DOWN PEDAL (LOCAL PICK UP) HAVE 2 HAVE A SOLID PROP SHAFT YOU CAN USE FOR THE CAV BAR OR I HAVE 1 OR 2 BARS
  9. Parts for Sale
    Do not want to break it up........box....$250 i have a long rod rod & cav bar also $75 finishline handle...................$150 cav plates from biesemeyer.....$50 3 pc pully system and cable w/chain......$175
  10. Parts for Sale
    I'm looking for Engine Mounting Rails Pads Flywheel cover driveline ect. I'm starting from scratch. This is for a jet boat with a BBC.
  11. Parts for Sale
    Hey, I have a powerglide for sale, shorty with Art-Carr tail and driveshaft. Drive shaft joint was just replaced, has about 4 hours on it. The tranny comes with torque converter adapter. Nice 2 speed with reverse, great for docking and working through the no-wake zones. $500, located in...
  12. Parts for Sale
    Polished aluminum 736" wing. It is 32" wide by 23" deep. It comes with chrome tube struts for mounting and it is adjustable. $200 [email protected] or (949)248
  13. V-Drives
    My plates and hardware are in dire need of a strip and re-polish. What do you guys use to pull all of the calcium from the water off of the plates and turn buckles? I did it a few years ago but can't recall what I used. I want to get all of the build-up off of the plates and hardware so I can...
  14. V-Drives
    inspecting cavitation rod and parts and my spring is broken who sells new ones
  15. Boats for Sale
    For Sale $1,900.00 Former "Loose Cannon" Top Fuel Hydro hull. ... This is that last boat ran by Greg (although rumor has it we may be seeing him again?) I will sell it with or without the installed hardware as pictured. The pictures posted are this boat in action. Other pieces from...
  16. Parts for Sale
    $250 obo plus ride
  17. V-Drives
    I'm looking for cav plate hardware off a cole runner bottom. I have the cav plates but no pillow blocks or control arm. Anyone have anything laying around? The boat is a cole tr2
  18. Parts for Sale
    (SOLD)CAV hardware for circle boat or flattie I have most of the hardware for a cav assembly. 2 powerder coated black cav plates approx 15x31"+ 9 turnbuckles (could use a polishing) 10 finishline chromed plate pads (ok shape) 2 polished cav plate pad supports (were anodized but stripped and had...
  19. Jet Boats
    Ok, let's see pics of any detailing work done on pump parts. Please try to keep this a "pics only" thread, so name dropping and name calling don't get this thread locked. Let's see any and all detailing pics from suction housing all the way to nozzle. Impellers, inducers, bowls, droops, etc.
  20. Parts for Sale
    Vents,handles,ss exaust tips...909 660 0997.............................vents,handels,gas filler are sold...thanks...4"exaust tip are still avalible...
1-20 of 59 Results
Top