Performance Boats Forum banner

Discussions Showcase Albums Media Media Comments Tags Marketplace

1-20 of 129 Results
  1. PB Open Water
    2003 Essex Monarch 23’ with a 496MAG HO and mercruiser bravo outdrive. Just got an invoice from a shop that charged $660 for an impeller & housing kit. Parts only. + $300 for 3 hrs labor install. I’ve owned a few boats and have done a few impellers myself, granted, not on this boat...
  2. Parts for Sale
    Dominator Suction Housing and spares $400 + Shipping. 9.5 suction housing. It is fully dressed ready to build. Was assembled and installed in the boat but never ran. Its new. Machined for pop off and setup for jet a way. Std ultimate wear ring. Mechanical shaft seal, oil reservoir, tapped for...
  3. Parts for Sale
    Internal balance flywheel and bell housing in amazing condition. $120 + Shipping New port Richey, Fl 918 two six nine 8084
  4. Parts for Sale
    FOUND ONE ! Please ignore. -------------------------------------------------------------- Looking for a BBC bell housing (top mount starter preferred) for a 3 Pt. mount set-up. Camps directly to a Berkely pump. Thanks
  5. Parts for Sale
    coupler and bell housing are originial equipment item. Flywheel is excellent shape aluminum. coupler is $300 bell housing is $300 aluminum flywheel is $200 in shreveport, louisiana 318-687-9088 or 318-470-1482
  6. Parts for Sale
    It is 3 3/4" in length. $65 + shipping. Steve 760-39zero-07 three six.
  7. Parts for Sale
    Brand new out-of-box Probe rocker stud girdle for the standard valve layout heads listed below: C8VE C9VE D0VE D0OE-R A429 CJ Edelbrock Trick Flow Street/Strip CJ Blue Thunder CJ Complete with stud girdles and poly locks, $--- Stud Girdles Are Sold __________________________ Used water neck...
  8. V-Drives
    What’s the best/easiest way you guys have found to remove the output housing bearing and seal out of a Casale IN/Out box?
  9. Parts for Sale
    Big block FORD motor plates & polished bell housing 4/sale $350.00 plus SHIPPING 919-397-3553 LOCATED IN NORTH CAROLINA *** TRIED 3 TIMES TO POST PICS WITH THIS AD *** pics on Craigslist ...BIG BLOCK FORD MOTOR PLATES & POLISHED BELLHOUSING
  10. Parts for Sale
    Looking for a 454 BBC Powerglide Bell Housing Adapter I am trying to find a Powerglide Bell Housing Adapter to fit the 454 BBC I am going to drop into a '77 Riviera Race-Ski Boat I am restoring. It had the same motor in it's previous life. I want to be able to use the existing motor mount...
  11. Parts for Sale
    Looking for Dominator/ AT suction housing. Needs to have a hd shaft and double drill action. Im located in so cal. Im open to options. thanks
  12. Parts for Sale
    Berkeley housing double drilled front and back with gth hand hole cover, aqua met shaft included. One of the pictures has a magnet on the shaft to show it is aquamet $400 takes them both I am located in nor cal but I can bring it to Ming at one of the races
  13. Parts for Sale
    BELLHOUSING IS SOLD Brand new Owens marine bellhousing for a Ford 385 Series a la 429 460 514 521 533 545 557. This unit is brand new, undrilled, as cast, and as machined. Beautiful Buddy Bar casting. Can accept Owens trans, Lenco trans, B&J trans, etc. Accepts 164 tooth flexplate/flywheel...
  14. Jet Boats
    Anyone running this piece? Thinking about upgrading to this, as my old nozzle housing has a lot of wear on the inside where the o-ring is supposed to seal to prevent water blow-by. Is it a noticeable difference in thrust/top end? Also, the description states, "it has 3.5 degrees of built-in...
  15. Jet Boats
    Newbie to the forum with what may be an ignorant question.. Can anyone steer me in the direction that I might locate a transom housing that would work with this setup, or am I gonna need to just fab something to fit ? I'm certainly no stranger to a project or two, but to be honest as far...
  16. Parts for Sale
    Looking for a Big Block Chevy bell housing for a Lenco trans Thanks, (928)377-0553 Chris,
  17. Parts for Sale
    4 bolt Cover for a BBC, plenty of depth (2.5) to run a weighted fly wheel Minor polishing and back to new condition, 120.00 prefer local pick up San Diego area. 619 4476898 Adam
  18. Parts for Sale
    For sale by owner - Guardian Motor Mount/Bell Housing. $100 OBO. Please reply to thread with questions or to set up a time to view the part. We are willing to drop it off to a serious buyer within 20 miles of San Mateo, California.
  19. Parts for Sale
    1-BBC STUD GIRDLE,has been machined for extra clearance--------------$100.00 2-BBC STAINLESS CROSSOVER 1"NPT----------------------------------------$75.00 3-FUEL FILTER/WATER SEPERATOR--------------------------------------------$45.00 4-REX MARINE 4-PORT THERMOSTAT HOUSING/W...
1-20 of 129 Results