Performance Boats Forum banner

impellor

  1. Impellor ?

    Greg Shoemaker
    Greg, who is making the best S.S. impellor now a days ?
  2. impellor clearance

    Jet Boats
    putting togather pump with new aluminum impellor & ultimate wear ring. what is the desired clearance. Thanx
  3. Impellor question

    Jet Boats
    Will a American Turbine impellor out of a American Turbine pump Fit a Berk?... Supposedly it has a shoulder on the exit side that may or may not have to be machined off??? Only reason Im considering it is cause its a great deal and basically new, came out of a fishing boat but dont wanna jump...
  4. hp vs impellor size @ rpm with inducer?

    Jet Boats
    i have a chart but it does't factor in a inducer, anybody got any info/data of before & after inducer, rpm & hp # . so far i am spinning @6650 but the inducer has not been factored in. aa impeller = @ 9.25 [email protected]
  5. Impellor ?

    Jet Boats
    I was wondering if a AAA impellor is the same as a 9.5 or is it different size? What is the difference?
  6. MPD SS B impellor

    Parts for Sale
    Fresh MPD full race prep work. $900
  7. MPD impellor

    Parts for Sale
    Full race prepped MPD B impellor w/ > 10 hrs/like new. $1100
  8. Impellor chart

    Jet Boats
    If a pump is recently rebuilt and the RPM's are lower due to a tighter pump then according to the impellor chart I have less H.P. Is the impellor chart based on a new pump? Just trying to figure about where my H.P. is. I turn about 4300 with an SS "AA" impellor Berk.
  9. bad porpoise after impellor swap

    Jet Boats
    so i finally got my 19 daytona to go after playing with loader and bottom and the lawman for a month . So i am turnin a bc stainless at 6k thru double mufflers at 93.6 gps . Installed i believe a double a stainless brought the revs down a bit but from 77 mph to about 84 bad porpoise with...
  10. Impellor chart question.

    Jet Boats
    Can anyone tell me if a tight pump reads differently on a impeller chart than a loose one as far as H.P. goes. Also does it change if there is a stuffer installed.
  11. WTB AA or A Stainless impellor

    Parts for Sale
    Im looking for a stainless AA or A impellor in best to good condition! Even new would do if priced right! Let me know what you got! Thanks!
  12. berkely alum A impellor

    Parts for Sale
    got this for a spare. unknown but needs work on leading edge blades and wear rig areas. asking 75.00 you pay the ride! will make good spare.
  13. priming pump after impellor / thermostat change

    PB Open Water
    Changed the impellor and thermostat in my boat yesterday. Hooked it up to the hose using the under-hull suction cup deal, and can't get pump to prime. Fired it up twice for about 15 seconds each time, no water out the pipes so I shut it down. It is difficult to get a good seal around the...
  14. My impellor is JUNKED!!

    Jet Boats
    OK, So I got the high dollar rebuild, JG bowl, detailed impeller (Supposed to be an "A") Place and droop. Boat never went right compared to last year. Lots of caving and very "pipey". Still believe there are intake angle issues, but I don't know. Went out the other day. Ran about 20 minutes...
  15. ???? on changing my Impellor

    User "How To" Section
    ???? on changing my Impeller I took the boat out this weekend & it ran a little warm so i assume its the impeller, so my ? is how hard is it to replace it, I have a 496HO w/a bravo 1 out drive!
  16. SS impellor

    Parts for Sale
    A/B cut A little dinged up on the leading edges but nothing that cant be clean up unless you'd like me to clean it up. Otherwise detailed but by whom I dont know. Looks to be in great shape though. $600 (909)322-6708 -omar
  17. Impellor or not!

    Jet Boats
    I got to test my new boat this weekend, YES! Boat ran good for stock 454 about 60 mph turning around 5800-5900 RPM! Well you know when I got back home out comes the stocker in goes the bigger motor! I know the increase in HP is going to probley need an impellor change I am running an A right...
Top