Search Results for ‘inch’

I have everything except for rods and pistons to assemble a 500 inch bbc, there are some very high end parts that have not been run since freshening up, parts list as follows Bowie block, 4.600 bore, filled to the water pump, bushed lifter bores Bryant 3.75 stroke crank jesel belt drive gm...

I have a drill fixture for a bravo one pattern with drill bits and hole saw- $125 1 1/2 inch bravo one drive spacer- end cut for use on a 3 inch imco shorty- $ 150 1 inch bravo one drive spacer - $150 2 marine KRC power steering racing pumps with pulleys - $225 each in shreveport...

Mercruiser bulldog 540 engine with 165 hrs-$8900, is totally complete with stock exhaust system and serpentine belt drive assy, bravo one with same time with stainless steering bracket and stainless drive shower-$2850, imco 2 inch shorty with hd bearing support and 1 1/4 inch shaft$2850- brand...

BBC Exhaust logs with snails and 4 inch outlets .. These are not mine . i am just posting for a guy . they are in good shape . he went with Lightening headers and asked me to sell for him.. he is asking 250.00 or best offer. his name is Robert Webb. he bought the 82 or 83 Sanger mini cruiser...

Just wanted some opinions on what haul to go with. The motor will be 650 plus horse and I plan on get her over 100mph. Please no trash talk. Only serious comments and advise. I have both of these at my finger tips and am having a really hard time deciding. Throw me your choice and...

Fresh motor, 3 lake trips to get dialed in. 90MPH at 6000RPM in my Challenger bubble deck jet boat. Bowtie tall deck block, Scat lightweight crank, Eagle h beam rods, JE pistons 10.2-1, Crower 4/7 swap solid roller [email protected] 748 lift 112LSA. Comp rockers and stud girdle, polished ported Brodix BB2...

Have a set of these JE's i have maybe 3 hours run time if even that. this was Blown on E-85 .. i had a rod bearing start to fail and 1 piston got scratches on the skirt and i would not use it again , Block in that Cylinder got deep scratch as well so i bored it too .060 over and bought all new...

Sorry almost noramal, I have been working out of town , plus working on my motor issue, I never checked my post until today,,,,sorry I didn't get back with you guys,, so I'm still looking for a 11.5 x 15 left hand rotation , 1 inch shaft, if anybody else has one let me know, it might take me a...

Here is a very rare set of deep 13 inch reverse mount rims and tires in excellent shape. Rubber is almost new and these are the deep rims used by Ellis on all the bad ass flat and river race trailers.... These are by far the best looking low profile package out there..... $400 Located in...

Perfect shape 616-262-6076. Grandrapids mi

3-INCH thick MERCRUISER EXHAUST RISER SPACER PN # 93320A3 1983-2002 CHEVY V6 V8 MANIFOLD * Brand new * no hardware * only ran for 1 hour then pulled of because the risers were bad * I put these on when I was installing thru hull exhaust and needed the exhaust to tilt...

looking for a 2 blade for a flatbottom or the equal in a 3 blade just a river boat!!!!

WTB 4 inch stainless through transom exhaust tips. Rick 559-307-8008

Chevy 540 cubic inch, Dart Big M block, Edelbrock Victor heads andintake manifold for Holley Dominator Carburetor, CNC ported, Ferrea valves,Eagle rotating assembly, Comp cam & lifters. 10 to 1 compression. Neverlit. Built for my boat and/or my corvette. $10,000.00 818-585-4974

14x7 or 14x6 rims needed. Need set of 4 with or without tire. 3-3.5 inch backspace.

1 inch hydro prop 11 1/4 x 17 no name in excellent shape 150.00 541 915 0541

I am looking for a 4 inch steel crank for a bbc. Let me know what you have and where you are located. Can call or text 805 878 4772 if it's easier.

yeah what the title says what do you guys got

3 Inch spacers for split bowl 3 inch spacers to lower your thrust and get more lift. Split bowl pumps. CNC to size and Doubled drilled. $150.00

VERY NICE red anodized steering column with hub and steering wheel cap. Main column is 8" and hub is 2". Base is cut at approx 15 degree angle. Has 4 small threaded holes in main column (tach mount?). Shaft bushing missing. Take $100 plus shipping from 77351.... thanks...Don.