Performance Boats Forum banner

Discussions Showcase Albums Media Media Comments Tags Marketplace

1-20 of 24 Results
  1. Jet Boats
    I have searched all over and cant find any information, on how to install a Dan Olson block mount oil cooler on a Gen V bbc. Does any one have any pictures, of how they are mounted, or installation instructions or can lead me in the direction of where to find installation information? It would...
  2. Jet Boats
    I have removed the old packing rings and am ready to install the new ones....But I have a lot of white aluminum corrosion in the hole. My question: I know I am supposed to coat the inner side of each ring before installation with anti seize.....Could I coat the outside also so that it...
  3. Jet Boats
    Soooo, how exactly, is this suppose to be installed? Baught it from Marine Industries West, but no installation instructions came with and I can't find any thing online about it.
  4. V-Drives
    I am going to install a new prop on my Schiada. My past experience was: 1. See where prop fits on shaft w/o key. 2. Cut key stock to length. (Question? How long? I know, not to exceed prop dimensions) 3. Install prop with key on shaft and check position to where prop was w/o key. 4. Install...
  5. Jet Boats
    Tried to install a new marine Faria fuel gauge last night, dash is too thick, can't make contact with the back clamp:wtf: Never thought I'd have to take that into consideration. Thank goodness I only bought one gauge. Replacing my dash isn't an option. Am I gonna have this problem with all...
  6. PB Open Water
    I'm interested if anyone has any knowledge of what is needed to install a Honda Generator on a boat for battery backup. I had a huge 300lb battery for my stereo and am over it. I like the idea of the 47lb generator that I can use for other purposes. I think I remember hearing about needing to...
  7. Jet Boats
    Just pulled the pump and intake out of my boat due to a leak. Now when I put the intake back into my hull I'm looking for some advice. I have read about what sealant to use but I'm looking for help on setting the intake into the hull. Angle/height? What should I be looking at.
  8. Greg Shoemaker
    Okay............tried everything I know of so my last resort is to confess I don't know what I'm doing. I am trying to install a new steering cable on an 18' Sunkisst. Installed the helm and wheel with no problems. Installed new rubber groument thru the jet drive, have put the steering tube...
  9. GN7 On the Dyno
    I just bought a used Whipple 2.3l EFI that I want to set up on a carb 502. It's pretty complete with fuel pump and ECU. I'd like to get some installation instructions to figure out the wiring harness. Any ideas?
  10. Paint and Fiberglass Repair
    in a general rule of thumb kinda situation, i have read that the wood used for a bulkhead in a vessel shouldnt actually touch the outer fiberglass structure of the boat. this is because as the boat flexes the wood will not and it will crack the hull from stress. it should be mated to the outer...
  11. Parts for Sale
    Completely rebuilt Mercruiser Bravo XR outdrive. This drive has not seen water since a full professional rebuild by Extreme Custom Marine. 1.50 gear ratio. This is a late model swept back case style XR. This unit is very clean with no corrosion. Keeping breaking stock Bravo One drives? A...
  12. Jet Boats
    I have a 1984 19ft bahner and was wanting to put in a bulkhead. I read on another thread to be sure to leave a gap for expansion and contraction. But before I glass it in I wanted to know if anyone knew why they didn't put one in to begin with. Is there a specific reason there's no bulkhead? Thanks
  13. V-Drives
    I have a 12 degree Casale and installing a prop release . Question is this , when I pressed on the double row main output bearing and pressed the assembly into the case the bearing sticks out .344 and the receiver groove in the extension piece is .345 deep . What is the crush value at that...
  14. GN7 On the Dyno
    Does anyone happen to know if a video is out that shows how to install a comp cam 6200 series belt drive. Thanks
  15. West Coast - South
    Anyone know of a good place in Havasu to re do my pontoon carpet? Thanks for your help.:)
  16. Jet Boats
    Ok guys I am questioning myself. I heated up the insulator ring and as it was melting i removed the brass wear ring. The insulator looks ok I think. My new wear ring will not go in. Do I need to heat it up again and slide it in? I have a pic I will post in just a few
  17. Jet Boats
    Hi All, I thought I would share some pics of my recent rail kit upgrade. Getting ready for re-power with a Dart 540. Special thanks to Tom and Josh at JBP! I went with their rail kit, but had them wait to mill the pillow blocks until I knew the angle I wanted... Used Jim Brocks...
  18. Jet Boats
    Hey Everyone! Well, after almost a 3 year hiatus "Dad's Boat" is making a comback! I finally killed the 454 and am in the final stages of putting together a Dart 540. (working with Steelcomp and cstraub on the combo) During this repower project, I will also be eliminating the cast aluminum...
  19. Jet Boats
    I have searched and searched but there is not much info on installing a Calgo steering. I know there are many of You out there running the Calgo and would apreciate any instructions on how it is installed. What do You do with the cables that run down the side of the boat? Is it better to run the...
  20. Jet Boats
    I remember reading in a thread about how to mount the rails ,But I cant find it. I thought I remember socal saying to mount paralell to the sringers and cut the plates to achieve the proper angle of the engine in relation to the pump? Should the rails be flush with the top of the stringers,or...
1-20 of 24 Results