Performance Boats Forum banner
1-20 of 26 Results
  1. Parts for Sale
    BBC Factory Aluminum High rise with adaptor off my Super Stock motor. It has the "legal" cut out in the plenum divider. It's a spread bore flange with 1 2" tall 4150 phenolic adapter as required for Super Stock. No leaks, no stripped threads. It's painted gray and has no issues. $50 +...
  2. Parts for Sale
    Intakes for bbc 18 degree pontiac big chief 427 casting heads New weinle motorsports weld up kit. 500.00 Used tall runner no top. 500.00 Complete kinsler stack injection flowed by gene adams. 3,000. 618-567-1804
  3. Parts for Sale
    I have two Edelbrock Performer intakes in great condition for a small block Chevy I would like 75$ each Call or text 661-406-2448 ask for vince
  4. Outdrives
    Working on my big boat. I just installed a new SEI bravo lower due to the old one being all corroded and drain plug corroded in. Now I have gear oil leaking out of the water intakes on the side of the new lower unit. my setup is a 1989 bravo 1. The new lower unit has the extra oil passage that...
  5. Parts for Sale
    I have a freshly rebuilt dominator 1050, painted blue. $450 also availabe throttle bracket, fuel feed line, and secondary return spring kit. Dooley Scoop for single dominator with new arrestor. $175 Team G single plane air gap intake, 4500 carb base and rec port. $100 Professional products...
  6. Parts for Sale
    Have a Long list of parts here.. most intqake manifolds are New or like new. all parts were from a Machine shop from customers not paying for orders.. SBC intake 1. Air Gap intake # 7501 single carb like new or new 125.00 BBC intakes single carb's 2. BBC Edelbrock Victor JR intake Req...
  7. Parts for Sale
    Hi, I have some BBC blower stuff for sale and the list is below, everything is OBO + the ride please call Jeff @ 1415-202-3802 or pm me. Thanks 1. New Enderley tall big and ugly (BAU) 5 inch butterfly's only used for mockup and was to big for my application never ran, at Good Vibration...
  8. Parts for Sale
    WTB Berkeley or Dominator Jet Cores and intakes , PLEASE NO CRACKS OR WELDS , PM or call with what you have 805 466 4719
  9. Parts for Sale
    Intakes, V-Drive Stuff & Glenwood BBC Exhaust Nice V-Drive Handle ($50.00) + shipping Brass-Bronze Prop. 1", 3 blade, stamped 12 X 14. ($70.00) + shipping Large Idles Pulley & T Bolt. ($85.00) + shipping 6" Fuel Pump Extention & Drive. ($90.00) + shipping Gaffrig 10" x 5" Stainless...
  10. Parts for Sale
    Intakes are for bbc 18 degree pontiac big chief 427 casting heads new weinle motorsports weld up kit. 500.00 used tall runner no top. 500.00 complete kinsler stack injection flowed by gene adams. 3,000. 618-567-1804
  11. Parts for Sale
    Looking for two engines worth need the oval port ones. Three piece intakes EFI Thanks Eric Send PM
  12. Parts for Sale
    502 MPI Complete vortech (like procharger) Supercharger kit Hi, I have the following for sale in great condition. Complete livorsi/graffig extreme supercharger kit. Polished Vortech V2-S SC Polished Intercooler, re-programmed mefi 3 ECU and 2 bar map sensor included ready to run! fuel pump and...
  13. GN7 On the Dyno
    thought this was pretty good: 278/284 @ .050, .780 gross lift Set the lash before the 4th July weekend: set at .024" cold three day weekend put about 110 miles in the engine. Went back last weekend and put a bit over 30 miles on it on Saturday. Decided to run the valves tonight and 15 of...
  14. Parts for Sale
    a few intakes check pics. looking for 125 each for singles and 200 for tunnel ram its drilled for nos.
  15. Parts for Sale
    SBC-edelbrock toker ii used 75.00 SBC-edelbrock perfomer-with egr-#3701 new—150.00 SBC-edelbrock perfomer eps nonegr #2701 new 130.00 SBC-edelbrock victor jr tall #2999 used 200.00 BBC-edelbrock 454r victor jr #2902 rec port 4150 used 200.00 BBC-edelbrock performer 2.0 #2161 oval port 4150 new...
  16. Outdrives
    I beach my Formula 292 Fastech a lot-with the low water only pick ups its a PIA trying not to suck up crap (which I have done before). Would it be acceptable to install thru hull fittings and a strainer and bypass the outdrive pick ups? I dont do a lot of rough weather boating so it stays in...
  17. GN7 On the Dyno
    What epoxy or other product are you guys using for aluminum head or intake repairs? I have an Edelbrock tunnel ram that needs all the runners filled about .060" or less x about 2" on 1-3 sides depending on the runner to match up with some AFR 305s. I'm afraid that much welding will warp the heck...
  18. Parts for Sale
    Offenhauser Turbo Thrust 360 polished single carb tunnel ram. Fits Ford 429-460, complete with Holley 4779 750cfm carb and Hilderbran style scoop. $500.00 plus shipping, located in Fort Mohave AZ. Email [email protected] for pic's
  19. Parts for Sale
    I have a Torker that is in nice shape has not been modified. Also have a Performer, plenum divider has been cut down, port matched to Mr Gasket ultra seal gasket, has a hole behind the carb that is 1/2 NPT this is where I had my pcv valve. I will get some pics posted $125.00 for either one...
  20. Jet Boats
    Looking to put together my swtd this winter. I have a stock berkley intake. i wanted to machine it for a shoe and ride plate. is this going to work for me or is a low profile intake 100% better? I am running about 850hp.(give or take). I am wondering what the pro's and con's are. Any opinions...
1-20 of 26 Results