leaking

I spent the last two weeks at Trinity lake in N.Ca....Been doing it since 1965(Oh god I'm old.....) Anyway, I noticed a drip-drip from the shaft seal so I tightened it a little and it stopped...next day, after running over to the marina it had started again....Every other day I tightened it and...

Bad cores no problem.... any that fit 10-xx blowers

I just bought a 1978 Glastron Carlson cvx 20 and it came with a 1994 Johnson 175 ocean runner when i first went to look at the boat i looked in great shape the guy even started it up and let it run for me he put it in gear and rev it up it sounded great and the "pisser" was shooting out a good...

deleted

Are the cylinder seals replacable on the Dana tabs? I have 1 that is leaking and don't want to replace the whole cylinder if I don't have to.

Does anyone know who makes this thru hull hardware? With the hose clamp as tight as I can get it the blasted thing still leaks and the hose looks to be brand new. Seems to me I remember a thread showing half moon shaped pieces that went on the outside of the hose to help the hose clamp put...

I just recently topped off both of my tanks, one is now down to 3/4 and the other is still full but they both appear to be leaking fuel out and spraying down the sides of the boat when trailering. Do I just need to not fill the tanks up all the way or do I have a problem with my vents. Boat is...

Ok, so here is a weird issue. I found about 2quarts of oil in my bilge after I backed my boat down a very steep ramp at my in-laws. Its a 73 Tahiti with a rebuilt 455olds with about 15hrs on it. I pulled the boat back up the ramp, and saw oil and what looked like water running towards the back...

So I had a great river trip to Fishers until our run up to piccacho, and I noticed my carpet was wet. Turned out to be fuel leaking from my bow tank. Its a 73 tahiti, and it has the original gas tank up there. I dont want to cut more holes in the boat for side mounted tanks nor deal with more...

I have a 80a endrale cam driven fuel pump that is leaking from around the area where it attaches to the end of the cam shaft is there rebuild kit or an O-ring that I can replace or is this a common place for a leak to start or would this mean I need a new one? Thanks Grant

Hey Guys went to Parker for the Memorial holiday, Didn't get much run time due to my boat taking on too much water, Looks like when the original owner stripped the boat for paint he didn't use all the proper gaskets etc to stop it form leaking so he used heavy amounts of silicone, long story...

So I do the annual oil change in the drive and I figure that this time after pumping the oil to the vent hole, I will plug the vent and keep pumping oil to the bottle in the transom, instead of filling from the top of the bottle down. After screwing the vent plug back in and pumping oil from the...

I need to buy a lee turbo intercooler core. Anyone have one for sale call 318-687-9088. gary thanks

Here's one for you bravo 1 experts... I had the drive rebuilt 15 hrs ago..been to the lake 4 times....I get an alarm and see the drive bottle is getting low...I top it off...(after 3 hours running it).. figure drive maybe burped some air,,no biggie..then I find oil/gear lube in transom...start...

I have a tile shower with a mud set pan. About 5 years old. Now leaks onto the ceiling below. I realize it is probably the fault of a poorly installed mud set pan. I will replace all the possible troubled grout areas. I can see it leaking around some edges and the drain. The question is, is...

As with everything else on my triple axle extreme trailer, It's time I learn how to fix a sealed bearing. So far I've had to re bleed the brakes, replace premature wearing tires, replace the wench and get new bolts for the spare as the ones put on by the factory person were installed cross...

How much salt should I be using? I seem to use about 60 lbs a month.and about 1 to 2 inches of water a week.I noticed the deck raised under the pool sweep attachment about 3/4 inch for about a year now.I plugged the sweep attachment and bumped the pump to about 15 lbs and closed the jandy valve...

I bought a new battery for my project boat, hasnt ran in over 2 years. Started right up. Throttle response was good and everything seemed to be working fine. However I noticed a small hose at the back of the block (bbc), with a screw and a washer on it that was dripping oil all over the...

I have a 2003 21' Aftershock Tornado with a Merc 350MAG and Bravo 1 drive. The engine has a 100 hours on it and the previous owner put a new impeller and thermostat in last season and I just had all the fluids and filters changed Memorial Day. My problem is is that when my engine is NOT running...