Performance Boats Forum banner

Discussions Showcase Albums Media Media Comments Tags Marketplace

1-20 of 88 Results
  1. Parts for Sale
    Took these lifters out of a good running lake boat with small cam. They are in great shape. in shreveport, louisiana 318-470-1482
  2. Parts for Sale
    brand new bbc lifters in shreveport, louisiana 318-470-1482
  3. Parts for Sale
    Thanks guys all parts are (SOLD)......Never ran Morel # 5374 Hyd Roller lifters came from Straub tech.. $350.00.. (Sold) Comp Cams used Hyd roller lifters #854 looks as good as new $175.00..(sold) Used set of mixed crane 1.7 Roller rockers good condition $100.00. (SOLD) I still have the Morels....
  4. Parts for Sale
    I have a full set of like new Comp Solid roller lifters for sale. They are part #866-16 .842 dia and .300 long. $300.00 OBO shipped in the 48 states. contact me via e-mail please. Jim [email protected]
  5. Parts for Sale
    Used set of Isky redzone .904 lifter for BBC. Straight no offset. 80 runs in a dragster. $300 + ride.
  6. GN7 On the Dyno
    I had customer send in a set of lifters for engineering review. The lifters failed after 3 passes in a SB Ford solid roller application. The lifters came to me. Customer's customer had bought them at a swap meet where they were sold as Morels. Well they are not Morels. The following...
  7. GN7 On the Dyno
    Morel sent me 15 photos of "defective" lifters that were sent in for warranty. When Morel designed their hyd rollers in 2002 they found that running a tighter tolerance on the valving to ID of the body would allow for higher continued RPM levels. That tolerance is a minimum of .0001" to .0002"...
  8. Parts for Sale
    Everything in this paragraph brand new free shipping 7809-16 push rods 5/16 7.226 $30 424 bronze gear Chrysler .484 shaft $50 .2100 SBC Magnum timing set $22 7372-16 Magnum push rods 5/16 7.800 $90 853-16 SBC hydraulic rollers $400 854-16 BBC hydraulic rollers $400 813-16 solid flat tappet Chevy...
  9. Parts for Sale
    Set of PBM hydraulic roller lifters. I never ran them. Bought them for a project but decided to skip the roller cam upgrade this year and just go with another flat tappet. I'm pretty sure that the guy I bought them from said they had about 120 hours on them but who knows. From what I can see...
  10. GN7 On the Dyno
    At Straub Technologies we have been working with several oil companies over the last 2 years to give the consumer an oil that functions the best with hyd roller lifters. Because Morels tolerances are so tight they need an oil that not only lubricates the engine but functions as a hydraulic oil...
  11. GN7 On the Dyno
    Looking for a pair of Crane 13532-2 retro-fit hydraulic roller lifters for a big block Chevy. Have been looking for a whole set but would settle for a pair if anyone has any. They seem to be non-existent at the moment so was hoping someone had some collecting dust on the shelf. Let me know what...
  12. Parts for Sale
    #2 Isky Solid roller lifters 200.00 #3 454 4 bolt .100 mark IV block with ARP Studs O-Ringed 450.00 #4 Holley 130gpm polished mechanical fuel pump BBC 50.00 Holley # 12-454-13 (Deal Pending on Fuel pump with Cory Hansen) >>> Buy fuel pump and regulator and package deal for 75.00 #5 Mallory...
  13. GN7 On the Dyno
    All the engines I have built have been with solids. I'm doing a 348 thats going to be a cruiser, but I would still like to check valve timing, push rod length and valve to piston clearance. Any way to do this? It's a flat tappet cam. Thanks Tim
  14. Parts for Sale
    I have 2 sets of Crower severe duty roller lifters for a .903" lifter bore. They have the tie-bars attached and have the wide wheel. One set is standard (push-rod cup in the center on both lifters) and one set has the push-rod cup on the intake lifter off-set .180". They are $100 per set...
  15. Parts for Sale
    Set of 16 Comp Cams roller lifters for a BBC. They are .842" OD and the push-rod cup is centered on each lifter. They come with removable tie-bars. $100 [email protected] or (949)248-0083 OOPS!!! Right box; wrong lifters. Crowers are sold. No pix of Comp Cams yet. Pix are OK now SOLD
  16. Parts for Sale
    I have 3 sets of used Crower severe duty solid roller lifters for a BBC (396/427/454/502). They are the cutaway model. Set 1: .842" OD with std. push-rod cup. $100 SOLD Set 2: .842" OD with intake push-rod cup off-set .180" for Big Chief heads. $125 SOLD Set 3: .903" OD with intake push-rod...
  17. Parts for Sale
    Big Block chevy Isky sold roller red-zone E-Z-Roll Lifters #372-96-RH Isky rebuilt and checked. Normal bore size. Used condition good shape all rollers check good. $300.00
  18. Parts for Sale
    PBM Machined alloy lifters, Double roller timing chain and billet gear. 8.100 and 9.100 pushrods. 250.00 for all of it. 352 266 1457 or [email protected]
  19. Parts for Sale
    Set of Crower severe duty lifters .842 lifter bore, high pressure pin oiling. 100 runs $150 + shipping Manley 221448-16 valve springs with ti retainers 100 runs $300 + shipping
  20. Parts for Sale
    2 sets of used roller lifters for a BBC. One set is for a standard BBC head with no off-set on the push-rod cup. $125. The other set are severe duty Crower roller lifters with a .180" off-set on the intake lifter to get a better push-rod angle on a Big Chief head. $150. [email protected] or...
1-20 of 88 Results