Performance Boats Forum banner

location

  1. NJBA September Race Location

    Jet Boats
    Josh, Kjell, Mike, did the board make a decision about moving the September race? Is it still at Bakersfield or??? Thanks! :))THumbsUp
  2. [Question] Canyon Marine HIN Location

    V-Drives
    I'm new to this forum. My name is Tom and I'm located in Corona California. I have a 1985 Canyon Marine drag hydro. I'm getting ready to start to restore and bring it back to life. My problem now is I cannot find the hull ID numbers. I'm sure they are covered with paint and I'm hoping someone...
  3. Question on changing motor location

    Jet Boats
    Motor is currently 18" from back of block to inside transom . Moving it forward to get 28-30" per Gregs advice. ( approx 1 foot ), Installing longer Stringer motor Rails ( I'd like to be able to just line up new rails where old ones were and re drill new holes in the angle , using existing...
  4. Location for kill switch on a RaysonCraft 21

    V-Drives
    Hi all, I never installed a kill switch in my RaysonCraft and was wondering if there are good and bad locations? I have a Morse Control and was thinking behind it. Towards the stern. Also, are any of the kill switches better than the others? Thanks for any advice. --Jerry
  5. Battery location in a v drive?

    V-Drives
    Just did a search and didn’t come up with much on different locationsfor mounting the battery. Mine is currently mounted between the block and transom,but it’s always a bitch to get to, (well not to get to, but to remove andinstall, and the added weight in the back Isn’t preferred. Wonderingwhat...
  6. keel pressure tap location??

    Jet Boats
    Anyone care to show where your drilling and tapping to get keel pressure reading? I know itll be in vaccuum and ill need to be able to read that but where is the best general location to take the reading from?
  7. [Question] alternator location on sanger mini v-drive

    V-Drives
    are there any v-drive Sanger mini owners that have photos of your alternator location and brackets. i have log manifolds and my alternator covers one of the water fittings when bolting it to the front motor mount. I'm not sure of the location of the alternator when the motor was disassembled ...
  8. Location in for sale posts PLEASE

    Parts for Sale
    From the "Rules" thread:: 2. Put city and state in all listings so people do not have to ask or guess where your item will have to ship from or where they will have to pick it up. It WILL help with sales!
  9. Kill switch location

    GN7 On the Dyno
    Where is the best place to mount a kill switch in a flatbottom and how long should the lanyard be? Thinking about hitting a race or 2 next year and didnt know if there was a specific location the sanctioning bodies may require it to be. Seems to me like a bracket on the stringer just in front of...
  10. Sub location issue ?

    Audio
    Hey Guys, I'm new here. Just picked up my first boat ( Monterey 190 ) and getting ready to put in a new sound system. My problem is sub-woofer location. My only real option is in the back engine compartment, which has tons of room, with a 12" sub for enough airspace. I MAYBE could fit an 10" or...
  11. Sanger Shovel Nose Hull ID Location

    V-Drives
    Help can anyone tell me where to look for the Hull Id # on a 1969 Sanger Shovel Nose, IM going to put this up for sale & need to get the title work inspected by a police officer and he has to see the Hull ID #s on the boat Thanks Carbonman
  12. Biesemeyer VIN plate location?

    V-Drives
    I have this guy coming over who wants to flip a 71 Biesemeyer Ski deck he picked up a couple weeks ago as rebuilder. He said he cant find the VIN plate. What are the typical locations for Biesemeyer VIN plates that I should look. thanks
  13. Subwoofer location

    Audio
    Question i just finished installing my stereo system. But yet to find a home for the 12" sub. I hooked it up and placed the box in several locations including on the nose of the bow And several other locations. The one location that sounds the best was behind the rear bench seat which is...
  14. Proper Prop Location on 12* Flat Bottom Rayson

    Propellers
    Can anyone tell me what the correct location (prop tip clearance with the bottom or distance aft of the strut) should be on an 18" flat bottom v drive Rayson. the prop is a 12x15 3 blade stainless. I'm installing a new gearbox and either need to move the prop shaft forward a couple of inches or...
  15. Intake Pressure Gauge Location

    Jet Boats
    I need a pic of where your pressure gauge is attached to the intake. Duane at HTP explained 1 to 1.5" before wear ring. I'm sure I can get it close to this, but it would be cool to see a picture.
  16. Meets - Location, location, location

    Michigan Hot Boats
    Let's get a discussion going on what the tentative meets should be for next year. This will give us a change to arg, I mean, dicuss the proposed places before the winter party so we don't waste time setting up the schedule and can spend more time bench racing. Please support your vote for a...
  17. Sub location...

    Audio
    Ok, let me see if I can explain this easily... I'm planning (this winter) a rebuild of my boat and am thinking that the best place for the subs is all the way up in the front of the boat, near the bow. I was told and I don't know if it's correct or not, that the best place to experience bass...
  18. rogers HIN location??

    Jet Boats
    looking at getting a rogers but there is no HIN on the back of the boat. were they stamped onto a plate and fastened onto the boat, or were they directly stamped into the boat? the game and fish guy says stay away from it since it may have issues with no numbers. but aside from that the boat...
  19. Anybody been to this famous Hollywood/Studio City location?

    PB Open Water
    George Barris has built some bad ass machines over the years. I have bid on two of his Batmobiles over the years. There are 5 originals from the 60s. He is one talented dude.
  20. Shifter Location

    Jet Boats
    Hey guys I have another question... I am building custom seats and my shifer won't work in its original location. I am thinking of moving it to the floor. I have a pedal for the throttle so I will only need to ise it at the docks. Has any one done this and are there any rigging pics floating...
Top