Performance Boats Forum banner

make

  1. GN7 On the Dyno
    Customer was having issues with getting his geometry correct. His OEM heads had longer valves and one of my camshafts. So the Geometry had changed. Here is his story: Well to follow up with my last post with my valve geometry all out of wack. What happen is I had my my 781 heads sent out and...
  2. Boats for Sale
    28' cat hull+ MOLD make offer 28' cat no trailer mold+ HULL 480 396 3455
  3. V-Drives
    Anyone recognize this boat. It has a 1963 421 Pontiac with a top loader Casale. Love the old school look, engine far in the back with lots of area in the rear seat.
  4. V-Drives
    1978 Eliminator 18' V Drive "spider" ?
  5. Jet Boats
    wrong place x
  6. Jet Boats
    So the Pink slip for my boat Says Centralma, The prefix For the Hull ID# is CN, it is a bubble deck jet boat. Looks similar to eliminator, Is it Possibly a Centurian Bubble Deck? I will try to add better pics later.
  7. PB Open Water
    When ever I pull up the reply page everything comes up but the reply box stays gray and you cant type in it. Help! I have trophies to show off from the St Michaels ACBS boat show thread. :wink2:
  8. Jet Boats
    Hull has JBX23852L393 what is the make of this 23' tunnel hull jet??
  9. Jet Boats
    Hi im new to the forum and new to jet boats. I recently bought a 1974 boat that im having trouble identifying the manufacturer and hull model. Here's the information i have on it, which searching internet and coast guard website have not gotten me anywhere. This info is what is on the title Year...
  10. PB Open Water
    Sold my v-hull boat early this year with 525, sounded great, love they way it performed and a great looking boat that caught everybody's attention. Purchased tritoon with 300 Verado to get by with and to my surprise it made a lot of since. After my great experience with the outboard I am...
  11. PB Open Water
    At Renegade power boats we sometimes accept trade-ins mostly depending on the condition of the boat. Being a center console boat builder my experience with inboards hasn’t been a whole a lot. From the inboard boats we have taken in I’ve had a great time my favorite part is definitely the roar of...
  12. V-Drives
    ALREADY SNOUT DRIVEN CLICK ON THIS LINK WOW http://www.performanceboats.com/boats-sale/296282-1977-sanger-18-3-circle-runner-%243-850-a.html
  13. Boats for Sale
    I am selling a 17'6" Graff runner bottom. The boat has has all hardware, fuel tanks, 2 drive lines one from Crank and one for 2 speed tranny, 1" prop shaft and prop. It basically has everything except the 10* Vdrive and seats but does have the stringer seat brackets. I was told from the boat...
  14. Jet Boats
    Got a deal on this old girl but had to drive 500 miles to get it. Had a 454 but will have a 557 Ford soon. Doing the pump now. Kept the intake and installed my cav reducer and stainless AT imp., AT bowl, berk droop and new FTN place diverter.
  15. PB Open Water
    I love my MCOB and I think the mid-cabin would be perfect for overnighting if I had some filler cushions. Does anyone know of anyone who makes filler cushions or have some tips on having them made/making them? I saw a great example of what I'd like this morning on this Eliminator V hull: 2001...
  16. GN7 On the Dyno
    I have a 454 (mid 1970's) LS7..compression is 12 to 1, serious over lapping cam (no specs), tunnel ram with 450's, iron heads. The carbs have always been too small. I have an opportunity to pick up some near new Edelbrock 750's very cheap. The advantage of the Edelbrocks is that my fuel lines...
  17. Boats for Sale
    2004 Entirely rebuilt '86 26' Scarab. 2 new 300 hp 350's with captains choice exhaust. New gauges and controls and trim tabs. Powdered coated wind shield gas cap and other goodies. Garmin Gps compass and marine radio. New stereo still in box (clarion) and 4 hew speakers (Infinity).Trailer gone...
  18. GN7 On the Dyno
    Frustrating.......:))ThumbsDwn So after mock up I thought I was good, but after final valve lash was set and spun the engine over a few times it appears im going to have to cut and weld my guide plates to get proper alignment. Anyone know who makes a 7/16" adj guide plate bbc conventional...
  19. Parts for Sale
    srp pistons 501 ford $50 sale pending 460 ski tow new $50 pure power remote oil filter $75 prop 12x15 lh 1 in shaft $25 3 blade ski prop cole tr2 splash guard red $100.................sold 20' schiada windshield $50 460 weiand tunnelram with spacer $200 sale pending foot pedal$25 ross pistons...
  20. V-Drives
    I am putting the exhaust together (glenwood wet), I have never put silicone or anything on the gasket between the main header and the elbow but I noticed a really deep cut right where the mating serfaces go together, I took a picture of the side that is ok just so you guys know what im talking...
Top