Merlin III Mark IV CHEVROLET CLONE BLOCK - 540 CUBIC INCH short deck block – has been ran for less than 500 miles on street– (piston failure) All other parts of the rotating assembly are good and ready for new piston/ring set and put back together. Will sell all short block parts as unit or...
Hello. Looking for an older BBC Merlin 10.2 1 PROBLOCK deck height .400 raised cam. These are no longer made and will need bore no bigger than 4.600 Thanks
320cc port matched runners. 119cc polished combustion chambers Raised D port exhaust. 2.300 1.88 stainless back cut valves. Fresh 3 angle valve job, fresh deck. Sold with check springs only. Clean bill of health. In SOCAL.
Complete engine ready to install and run - Hotrod, Truck, Boat, Plane.... anything!!!!! Builder says he will prep it for a boat application if wanted.
This is a complete Turnkey ready-to-run Supercharged 588" engine:
Merlin Alum Block 4.625” Bore
Internally Balanced, SCAT Crankshaft 4.375”...
Deal Pending with STEVE FAIST.........468 BBC engine. It is a BBC 2 bolt block with merlin cast 315cc runner heads set up as a solid roller cam . chevy rods with Bushed wrist pins and ARP 3/8th bolts . Grose Engines did all the Machine work on this engine and also picked out the cam and was...
Combo Makes a 615ci / 10.08 Liter BBC
ACTUAL Merlin Pro Block ... Thicker Block than the II's & III's , Extra Freeze plugs in the front , Starter can be mounted on either side , etc etc.
Splayed Billet Main Caps
Block Just had $750 Worth of Machining done @ Shavers
Magged
Bored 4.600
Line Honed...
I have a Merlin Tall Deck Block with a 4.500 bore that is ready to go. It has been machined, decked, Mag'd ready for your rotating assembly. If you are looking for a rotating assembly I have one for sale. Crower 4.5 stroke crank and Oliver rods with ARP 2000 bolts.
Merlin III Talk Deck Block...
merlin pro block currently 4.605 bore needs 3 sleeves just had block magged 55mm cam roller bearing core 904 bushed lifter bores billet main caps splayed asking 800 for block can send pics through email or txt will post pics tomorrow
Merlin X rect Intake and a HP Holley 800 fresh water only and ran one season, switched to blower. Intake is set up to run a 4150 or 4500 carb and does come with flame arestor. $600 TYD
Merlin III vs Big Dart M. Im on the fence between the 2 blocks. Im building a blown alcohol motor and I need to decide between the 2 blocks. Any opinions on which way to go? Im sure this is a loaded question about the details.
Sorting through some stuff in the garage yesterday I see that I have six (or more) bare 990 heads, $50 ea and a good looking bare 188 head for $100, located in So Cal.
I have a set of merlin bill grumpy jenkins heads 345 runners that are new have never been run at all they have 2.30 Manley Iintake vavles and 1.88 iconel exhaust they come with new guide plates and studs. I paid 1800.00 for them. They won't work for what I'm doing. My loss your gain. Make me a...
WTB T-Tank , Basset headers BBC
ALL PARTS HAVE BEEN PURCHASED OR LOCATED .. THANKS TO EVERYONE ON THE BOARD ;)
Looking for some of the following parts..
looking for a T-Tank about a 5+ gallons with the stand..
still looking for a t-tank and a set of large tube Basset headers..
Bill...
Have a very nice set of Merlin BBC iron rectangle port heads for sale. $900. They have 2.25 intake valves and 1.88 exhaust valves. Chamber volume is 127.500. Also have flow sheets. Come with stud girdle and nuts. They where on a 525 blower motor and work very well. They have dyno time and...