Performance Boats Forum banner

metal

  1. V-Drives
    Looking for some thin narrow either aluminum or stainless material (rub rail so to speak) to go around my flat at the deck to hull joint. Boat originally had a thin narrow aluminum strip would like to replace it with something. any info on source for this material is appreciated.
  2. Parts for Sale
    Pontiac Big Chief sheet metal aluminum valve covers in good condition, asking $70.00 + shipping located in Lake Havasu Az.
  3. Parts for Sale
    Hi i have a few parts forsale i was going to build a motor but decided to go different route Jonathan 951-538-2115 10-71 moonyham blower $2000 new price teauge super chiller fresh polish and gaskets $1000 SOLD! blower shop billet chiller tested good $1500 SOLD! Hogans sheetmetal blower...
  4. Parts for Sale
    BBC sheet metal intake for PSi screw BBC 9.8 deck sheet metal intake for PSI screw blower intake is built for Lee intercooler has bungs for fuel injection Pm me for pic can't upload for some reason phx az 1500
  5. Parts for Sale
    Custom sheet meal intake for BBC from TRE Competition Engines.... 9.80 inch standard deck with top for dual 4150 series carbs... Intake is fully plumbed for port injection nitrous system including valves..,,, Super nice manifold.............. $1300 OBO... Located in Lake...
  6. Other Stuff for Sale
    MY NEIGHBOR JUST TOOK THIS DOWN AT THE SIDE OF HIS HOUSE AND CLOSED OFF HIS GATE.... ITS IN NICE CONDITION.....SELLING IT FOR 1/2 PRICE OF NEW.ITS THIS STYLE....$800 OBO
  7. Jet Boats
    All along my bow the gelcoat is completely oxidized. It won't hold a shine for more than a week after it has been polished. I was just out wiping it down and the metal flake was coming off on the rag. What kind of options do I have? Or do i have any short of re-gelling the boat? It's just the...
  8. Parts for Sale
    9.8 deck conventional head, 3/4 Uhmw plenum spacer, dual 4500 top, and linkage. Never bolted down or ran. Intake has been Anodized black. $1850 Can also include the matched Gary Williams 1250s for an additional $1300
  9. GN7 On the Dyno
    My last engine chewed up the bearing pretty good. I have all the oil lines and dual oil filter mount removed. What is the best way to clean the lines and mount?
  10. PB Open Water
    Anyone here into metal detecting/treasure hunting? I seem to have a new hobby now. I got three detectors at a garage sale this summer. One is an older Whites coinmaster, one is a newer Whites XLT and the last is a Garret SeaHunter thats waterproof for diving. Any diggers? What kinda...
  11. Paint and Fiberglass Repair
    I have 89 vision boat and the clear gelcoat is almost completely gone and the metal flake is exposed. It is faded from sitting in the sun! I need to know if you can gelcoat over it and if so what kind of prep work needs to b done. I really want gelcoat the whole boat with different colors and...
  12. GN7 On the Dyno
    Calling GN7 and all others Every 2 or 3 times out I run a compression check and look under the valve covers. After compression check I pulled valve cover to look and double check valve lash and this is what I found. All of the shavings were on even side 2,4,6,8. I noticed 1 piece on valve cover...
  13. Paint and Fiberglass Repair
    my boat (the one as my avatar) has metal flake in the brown stripes and no matter what i do they wont stay shined for very long and feel rough. All the yellow is good and smooth and stays shiny. My question is on the brown parts of the boat is the gel gone or is there something i can do about...
  14. Jet Boats
    my boat (the one as my avatar) has metal flake in the brown stripes and no matter what i do they wont stay shined for very long and feel rough. All the yellow is good and smooth and stays shiny. My question is on the brown parts of the boat is the gel gone or is there something i can do about...
  15. Political Rhetoric
    Hagel cancels new medal Hagel cancels creation of new drone, cyber medal following widespread criticism | Fox News WTF was he thinking in the first place? :duh:
  16. Classic Hot Boats
    Meguiars Metal Finish Polish, this is the best metal polish I have ever used, works on aluminum, brass, copper, chrome and stainless. Best of all it is easy to use. I got it at Advance Auto, it is $14 can. Just thought I would let you know about it, you still have a couple of months to get...
  17. V-Drives
    Just thought I'd check if anyone had a rail kit or some 4x3x1/4 l T6 6061 L metal they wanted to part with before I order way more than I need. Each piece needs to be 30" long. Thanks.
  18. Jet Boats
    Where can I go to get metal pieces made in the LA area? I need a bracket made for this fuel/water separator
  19. Parts for Sale
    Well kids all/most of the Olds parts I have are headed to the scrap aluminum/steel yard early next month... Intakes, exhaust, cranks, blocks, heads, pistons, rods....... I can't store them any longer, and it seems as though no one needs them, so I'm cleaning out the shop and loading them on the...
  20. Paint and Fiberglass Repair
    i asked this question at another site. I have a set of aluminum gas tanks that are powder coated. I want to ether re powder coat or gel coat to match color on boat. will gel coat work for what i want to do? some flexing of the tanks but no more than the flexing on a boat? what do you...
Top