Performance Boats Forum banner

Discussions Showcase Albums Media Media Comments Tags Marketplace

1-20 of 119 Results
  1. Parts for Sale
    SOLD Billet engine plate mounts Used polished/billet plate mounts, 2inch wide, 4 for $55.00 plus shipping.
  2. Parts for Sale
    5 new bravo style motor mounts all 5 for $200.00 plus shipping
  3. Parts for Sale
    $300 for rail setup 23.750 wide Located in West Valley
  4. Parts for Sale
    2 front mounts for 460 Ford. Bottom one is 1/2" thick, top one is 3/8" thick. Both are made from 6061 aluminum. Take your pick, $60.00 ea. + shipping.
  5. Parts for Sale
    Looks for a set of Motor mounts and feet for a BBC...Anything out there?
  6. Parts for Sale
    I have 2 of the flywheel cover mounts and 1 of the front mount. Glenwood shows Chrysler 361, 383, 413,426 and 440. $100.00 each + ride. Or pick them up. 95604 now and will be headed Long beach tomorrow, I can take them with me.
  7. Jet Boats
    Hello all, I have a question about possible interchangeability between an Oldmobile 3 point mount and a Chevrolet engine. Would be a temporary kind deal, but I'm curious if there are engine mounts for a Chevrolet block that would bolt onto the Olds front crossmember/mount? At the time I was...
  8. Parts for Sale
    I sold the long block so I'm parting out the rest. This engine was in good running condition and would still be in my boat if I didn't switch to Big Block Chevy. Parts available: 460 exhaust logs w/snails. I believe they are Hardin style- $300 Front mount. Includes extension brackets- $50 Rear...
  9. Parts for Sale
    For Sale: Front and Rear motor plates. Front plate is made by Edelbrock Rear plate is Glenwood. $250 for both plates + shipping. UPDATE!!!
  10. Parts for Sale
    Looking to buy the following small block Chevy front mounts: Edelbrock Sanger Nicson ...may be interested in other vintage cast aluminum timing cover/motor mounts as well
  11. Parts for Sale
    Way back when, Gale Banks made the water jacketed turbo risers for their twin turbo setup that had provisions built into them for wastegates. I've done some homework and spoke with Banks and they told me my best bet is finding a used set since they have not been made for many years. Please let...
  12. V-Drives
    ... so the IMCO SS puke tank mounts suck. They always break at the weld and look pretty cheesy (IMHO). I keep using them because it would take serious time for me to scratch one out on my manual lathe/mill. So is anybody making/selling anything better? Thanks!!! PS, I can't wait to see what...
  13. Jet Boats
    I made new wind screens and need mounting hardware. Screens are on an open bow hallett, similar to the screens on a carrera, ultra etc. Problem is to find a clean way to mount them. Originally, they had a heat pressed tab about 6" apart to mount with flat hardware. The new screens are molded to...
  14. Parts for Sale
    ​I have set of Nicson engine mounts that fit FE Ford engines (front and rear). Asking $350.00 plus the ride. Call (626) 375-4286 ask for Lynn (no texts), or E-mail to [email protected]​ !!
  15. Parts for Sale
    This is the boat cover off the spare parts boat, I have the brackets that go on the trailer as well as the new canopy. 400.00 located outside Reno nev. Needs one end of a post made.
  16. Parts for Sale
    For sale, brand new accusump with billet mounts and new canton ball valve, will even throw in the fittings if you let me know the sizes desired. I don't remember what it's worth so I was thinking 200$ let me know will ship Andy 5628796387
  17. Parts for Sale
    For Sale , Big Block Chevy engine mount kit, I installed a rail kit so I have Engine mounts Top Mount Starter (works great ) Alternator with brackets Hardware I do not know what to ask so I am open to offers, I am located in murrieta CA
  18. Parts for Sale
    12 inch bundle 3.5 wide Copper-nickle has extra cooler for power steering SS mounting with rubber 120.00 352 266 1457 or [email protected]
1-20 of 119 Results