Looking for: (1) HPH Droop for Dominator https://www.placediverter.com/home/product/high-performance-housing/ and (1) Nozzle (manual or hydraulic) https://www.placediverter.com/home/product/place-for-dominator/

Bought a odd duck cheetah 18 winger last may and stuck it back while I built another twin turbo ls setup to put into it and now that motor is wrapped up I'm turning attention to the boat. Cheetah hull from the wicked molds, in decent shape but has a full setback Jacob Gonzales thinks he set at...

Berk R nozzle with removable insert and "ram's horn" reverse gate. New o-ring. Pivot pins & tiller inc. $390. 949-631-2040

I will soon have a Berk L3828 race nozzle and I need a reverse gate. Do I have any options or is the rams horn reverse gate the only gate that is compatible w/ this nozzle??? I don`t need reverse but I do need neutral. thanks in advance for help.

Took off a pump that I just picked up as spare, don't need the bowl. Don't know any history of it. $100 OBO.

FTN nozzles , how do you determine which one ? Took new setup out and with. purple (3") nozzle , Detailed SS "A" impeller ,Stuufer plate , and HM inducer ..motor pulls 6400 easily and hits limiter but doesn't blow pump out and stays loaded . This is only with 2# boost on motor ...I plan on...

Berkeley R nozzle w/ FTN insert Tiller arm, both power coated black Chrome ram horn reverse bucket All in great condition $250.00 plus ride if needed Located in Murrieta Ca (951) 440-7200

Weird deal i saw on fb, never seen anything like it was just curious how and if it worked

Nice FTN race nozzle with Rams horn bucket and steer arm. Has insert in it would have to measure it. No corrosion and its powder coated grey. PM Offer. Thanks

Anyone running this piece? Thinking about upgrading to this, as my old nozzle housing has a lot of wear on the inside where the o-ring is supposed to seal to prevent water blow-by. Is it a noticeable difference in thrust/top end? Also, the description states, "it has 3.5 degrees of built-in...

Berkley nozzle housing and rudder assembly used but in decent condition, located in Havasu , asking 135.00 Obo + shipping, Call Wally 928-486-1787

3.06", 3.09", 3.16" set of 3 for $75 plus shipping. These would cost $59 each new. thanks.

As stated looking for a used straight snoot race nozzle like this ------- open link and scroll down Hi-Tech Performance : Other Performance Parts

New American Turbine High Thrust Reverse steering nozzle complete with nozzle insert 3.25" $300.00 + ride 707-365-1802 Brian

Brand new HM race nozzle, has 3.125 insert... $600

Nozzle has yellow insert that is a bit worn. Bottom has been welded and smoothed. $140 located in Valencia CA PM me here or email [email protected]

About to really start playing with my hardware on my stealth. I am fully aware all boats are different but curious as to who all runs down nozzle with some up degree in the plate.

I'm looking for an angled nozzle insert for a Berkeley (heard they were used back in the day) so I can get a few degrees of upward angle out of my 12-JC, I don't have a diverter and I'm running a stock nozzle, located in Havasu, thanks

BERKLEY RACE NOZZLE WITH RAM HORN REVERSE BUCKET has 3.100 insert paint is in decent shape asking 200$ 619 322 9824 txt anytime or call after 6p.m.

BERKLEY RACE NOZZLE WITH RAM HORN REVERSE BUCKET has 3.100 insert paint is in decent shape asking 200$ 619 322 9824 txt anytime or call after 6p.m.