Performance Boats Forum banner

offset

  1. Parts for Sale
    Prefer smaller offset. Let me know what you have. Must be clean - not all cobbled up. Text and pics best. 831-595-4720. Thanks, Alan.
  2. Parts for Sale
    Dunn offset 4" BBC standard deck Very good condition. 9.8 deck chevy (will work with a 14-71) $350 plus shipping ($795 new) 949/283-four zero zero three Shawn​
  3. Parts for Sale
    looking for a offset pedal mount, anyone have one they will part with? I have the pedal assembly just need the offset mount. thanks!
  4. V-Drives
    Re-rigging and would like to off-set rudder. Which side for a LH prop? I will be upgrading to hydraulic steering also. This most likely will negate most torque feedback but I would still like to off-set to the best side. General ski/cruise... Thanks, HAP
  5. Parts for Sale
    4.5" offset mag drive, std. deck, bronze gear $450.00 plus shipping Call Tony 416 633-5419
  6. Parts for Sale
    Looking for a 4" Mag offset for a tall deck BBC. Either Dunn or Greer. Let me know if you have anything. Thanks Jason 818-522-6364
  7. GN7 On the Dyno
    Had a tough time finding a place for a cam sync. Gear drive cover has a little Bertha fuel pump in the way. Haven't found a place on a 44 amp mag for one yet. ;) Drilling for the pickup now. Used a 12 point steel bolt that doubled for the set screw for the pickup to see.
  8. Parts for Sale
    This is a very nice 3.2" offset mag drive that has mech tach drive and 2 lockdown tabs to help keep from moving under exstream conditions..i have a mallory supermag111 on it now but other mags may also fit;;you be judge on if your mag fit it or not..i went from rear location to front drive on my...
  9. Parts for Sale
    Dunn magneto offset for BBC Chevy standard deck. Works with MSD or Mallory. Spins free and is in overall very nice condition. Works with 14-71 blower/superchargers. These units sell new for about $800.00. I will sell it for $350.00. Shipping to anywhere in the lower 48 states for a flat fee of...
  10. Parts for Sale
    This was sold to me as a 4" offset but I believe it measures just over 3.5".It is for BBC standard deck. I ran this for a couple of seasons and had no problems with it. Someone drilled an extra pin hole through the dist.gear but I don't know why. This is for mag, cap and wires, offset, and coil...
  11. Parts for Sale
    What do ya got out there???
  12. Parts for Sale
    For sale Mallory mag 3 part# 29160-3 just done by Don Zig and a Dunn 6"offset rear drive with bronze gear and new belt, will fit std or tall deck block, $600 + shipping Im in Conroe Tx 832-527-2503
  13. Parts for Sale
    For sale: vertex OXC mag with external coil, wires and vertex 4" offset drive for tall deck BBC!! Complete setup $850 #270 276-5510
  14. Parts for Sale
    $1,500 each Both have polished mags and offsets. Top 2 pics are Hunt mag for tall deck, bottom 3 pics are Ronco mag for short deck. Private message if interested.
  15. Parts for Sale
    Still looking for a good used 6 inch Dunn offset Mag Drive.Anyone have one they don't need let me know. Jim
  16. Parts for Sale
    looking for a good used 6 inch Dunn offset Mag drive for a BBC 9.8 deck. Jim
  17. Parts for Sale
    wtb a Dunn 6 inch Mag offset in good shape.To fit a BBC 9.8 deck. Jim
  18. Parts for Sale
    Super Mag III & Dunn 6" Offset BBC Tall Deck Sold Mag and Offset For Sale: Super Mag III & 6" Dunn Offset.The mag was completely refreshed by Don Zig, and I mean completely.There...
  19. Parts for Sale
    Offset roller lifters 904 27 1/8 mile passes asking 165 shipped or trade for 45oo flange intake Rec port bbc
  20. Parts for Sale
    need offset and coupler for vertex mag it has to work with the vertex thanks
Top