Performance Boats Forum banner

Discussions Showcase Albums Media Media Comments Tags Marketplace

1-19 of 54 Results
  1. Parts for Sale
    Need a ovalport ram bbc with or without carbs
  2. Parts for Sale
    Edelbrock 7561 Air gap manifold, like new used condition...motor was in the boat for 5hrs $150 plus ride
  3. Parts for Sale
    I have a set of 049 BBC large oval port heads. They got replaced with aluminum heads, I took them in trade for someone who ended up not buying them from me. They look to be in decent shape, had considered just hand lapping the valves prior to the decision by the owner to replace. $400 in...
  4. Parts for Sale
    WTB Oval port BBC heads & Intake,Selling pair of 990 heads & Rec port Polished Intake I have a pair of heads on a 468 bbc Engine i have.. they are 990 GM rectangle port heads.. i will be keeping the springs and retainers for the new heads since the springs match my cam.. the heads are in good...
  5. Parts for Sale
    Looking for a set of oval port heads ready to run. prefer stainless or better exhaust valves, set up for flat tappet cam.
  6. Parts for Sale
    I am looking for an oval port tunnel ram for bbc 454 1 or 2 carbs
  7. Parts for Sale
    Selling my BBC Oval port Victor JR. Intake along with my fresh rebuilt Holley 750cfm DP Mech Sec. & Polished Scoop. $200 Carb - SOLD $125 Scoop - SOLD $200 Intake - Available Adam - (562) 277-3431 Lakewood, CA
  8. Bob Teague
    Starting the slow process of building my 502 MPI in the off-season. I was planning on going from to a 509 with 741 cam and CMI exhaust. I have a possible deal working on some Edelbrock heads. I want to stay around 9:1 compression. Which is the better head for my application. Rectangular or oval...
  9. Parts for Sale
    I have 2 sets of heads for sale, the first is a bare pair of 148 big oval ports that are good. The second is a complete pair of small oval ports (236) that have about an hour of time on them. The set of small ovals has had the chambers cleaned up on them, would like to get $150 for all 4 of them...
  10. Parts for Sale
    Building a stock fuel economic 454 , here are stock oval ports of a running BBC Contact Adam (714) 264-six429 asking $300 for the pair:partyguy:
  11. Parts for Sale
    I have a set of big block chevy heads that have been sitting on my shelf for a couple years and i have no use for them. The came off of my old jet boat and did not have many hours of run time on them. I switched out for aluminum. Anyways I have no use for them and they are just collecting dust...
  12. GN7 On the Dyno
    I have a 461 BBC 11.5 to 1, 660 lift solid roller cam. This motor had stock casting 781 oval heads with stock sized valves topped with a wieand tunnel ram with two 660 carbs. I have just got a set of dart pro 1 aluminum 310 heads. My question is how bad is the oval port intake gonna hurt me on...
  13. Parts for Sale
    Selling a wieand tunnel ram, oval port, 2 Holley 660 center squirters, fresh reuild, Rex marine red anodized throttle cable plate, new cable clamp, all new hardware, Rex marine hiem bar, mr gasket fuel pressure gauge, all new xrp fittings with new braided line, Holley regulator with custom...
  14. Parts for Sale
    Weiand oval port tunnel ram, 2 Holley 660 center squirters (fresh rebuild), Rex marine cable plate, Rex marine hiem bar linkage, new 33c cable clamp and stainless hardware, custom stainless regulator plate, mr gasket fuel preasure gauge, all new steel braided lines/an fittings, ready to bolt on...
  15. Parts for Sale
    Building two 454s for boat need pistons, matching cams and oval port Victors or same style.
  16. Parts for Sale
    pm me or [email protected] with your price an picture of it
  17. Parts for Sale
    Anybody have one around doesnt have to be pretty
  18. Parts for Sale
    No I don't want a rectangular manifold. Also looking for a pair of small carbs (600, 650, 660.)
1-19 of 54 Results