Search Results for ‘plumbing’

Who does plumbing in the IE? Have a leaky pipe in the slab at my Moms place, so need a repipe, prefer PEX, had the hot water dome that way years ago, don’t remember why we didn’t do the cold at the same time. Any recommendations? Will need the walls fixed too once they’re done with the plumbing.

Is it ok to run the dump line like I have it here coming out of the bottom of the manifold?

I bought a new to me boat and it has a pop off on the pump, it came with some controls and reg, some one cut all the lines and everything is in a box and a button on the wheel. Can someone put up some photos of plumbing or explain how to plumb it, Thanks

Hi looking for some ideas on setting up mercruiser heat exchanger in ski boat Need some recommendations on 1. water pickup either through hull clam shell, or transom (have no holes in boat at present), what size was thinking 1.25" dia 2. using a seacock, shut off valve 3. whether should be...

I'm wondering if I'm correct in my thoughts on Plumbing my jet boat. I'm going to run a line from the pump to the pressure relief valve and from that valve up to a tee fitting and into the water pump ports. Two lines out of the thermostat housing, one dumps overboard one has a valve on it to...

I purchased a 21ft Taylor Jet with a 460 Ford ....The boat has Kodiak Manifolds with stainless risers.....how do I know I the exhaust is plumbed properly? From the T stat housing water enters the manifolds.... There is also a port that has been blocked off on the front radiused part of the riser...

I'm about to start plumbing my twin turbo motor and I was wondering how to plumb the water lines. I have heard some people are doing a secondary water source for the intercooler. Is it ok to come off the pump, through a strainer with a pressure relief, go through the intercooler, in the logs...

Running a competition intake are the ports in the front of the manifold supply or discharge ports ? I have water going into Both the block and the front intake ports as you can see in the pic ......then there are two ports at back of intake that I have discharging overboard ..... my problem is...

I am looking for a recommendation for my plumbing, I do not want to deal with making all the AN lines. Looking for a place hopefully in the inland empire ( so cal ) to drop it off and they just handle it Thanks

Ive been boating for about 10 years, and after starting with a Yamaha LS2000 twin jet boat, have had a couple I/O boats in between. Just picked up a tricked out (ie mutilated) 73 Rally Sport Hombre turned hot-rod. On our 1st time out yesterday, it ran OK at first, then started dying at about...

I need a shot of the correct way to plumb a cruiser (v-drive trans cooler gear box cooler) with water logs and snails out the back.

I'm looking for some help on having the plumbing done right on my 454. The previous owner has hoses and valves everywhere. I'm assuming that this wasn't correct and I would like to get it back to the way its meant to be. I have a Mirage Jaguar Jet with a 454 in it. 8 years ago I converted the...

Does anyone know what this pipe is coming out of the exterior wall of my house just below my hose spigot? I have one by each of the hose spigots around my house. The pipe appears to have some sort of wire coiled up around it and has a soldered on cap. Is this an interior house water pipe? I...

I have a water pickup under the boat that I was going to use as the water source for my basset headers...anything special I need to make sure I don't blow anything up?

New to the jet boat world but I have been bitten. I have a BBC with logs running through the transom. I bought the boat and the last owner said it took a long time for the boat to warm up after you get it into the lake. It does take awhile, but it does warm up to about 150 degrees. I was on...

I was wondering if it is OK to use Aluminum line for hardlines rather than stainless? In particular for water lines. I want to do a few of our boats in all hardline, but I'd like to practice on the non-showy boats using cheaper and easier materials. The aluminum line is "not recommended for...

Hey Guys, Somebody had a handy dandy plumbing diagram for a 460 with OT headers and I can't seem to find it in the search tool. Can you guys help me out I'm trying to verify all is correct with my set up. Even if you don't have a diagram a brief description of how it's done will be very...

I am installing 3 auto bilge pumps in the back of a Sanger hydro. Can the drain lines be teed together, or do I need 3 separate drain lines going through he transom?

Since converting over to EFI I need to keep the motor at 200 while maintaining water through the exhausts. Anyone have a picture of their set-up before i dive into this? Currently it runs through the logs then into the block.. Thanks

kurtis Blower build intake Plumbing, ect. Motor installed in the Kurtis Have these 2 intake water ports do I just plug them?