Very rare Biesemeyer 4 point hydro full restoration in 2010. 572 CU inch Blueprint motor, 2 speed tranny, Casale v drive, all rigging by Tom Stolarz at WPM racing. The motor was rebuilt 3 years ago and the tranny is newly rebuilt just put back in. I have tons of pictures of the restoration and...
I am looking for some general information on the 4 Point Hydro, as I now have one as a personal project and trying to decide if I want to invest the blood, sweat, tears, and greenbacks necessary.
Have done one other (jet) boat build so aware of the pain factor, and though I like this boat and...
I have what seems to be a pretty stock 454 with oval port heads, flat tappet cam and dual plane intake. My plan is to use my ported 088 heads, matched dart intake and a decent hydraulic roller cam from my offshore motor. I will probably put new pistons in depending on what I find. Would these...
Up for grabs is a 3 point mount hardware needed to mount a 455 olds.
See pics.
Prefer to sell all together but may mix and match. $500 obo
text 512-755-2575
BBC or SBC THREE POINT MOUNTS COMPLETE SET 454 / Berkeley
Asking $300
Just removed this winter. In great working condition and original to my 1990 Commander
Complete with top mount starter
call or text
559-802-8827
Located in Visalia
Dominator 1050s on a very healthy 8/71 blown 555
Traded my e85 carbs , going back to gasoline .....
lost all my old data I had written down on old tune up , but that engine was 454ci and not near what this engine is
IIRC those jets were 89 squared
anyone out there on gas running something...
Morning coffee at McKenna's then plan on leaving Disco light house around 11:00am or so and head out towards The Point. Conditions should be good. :partyguy:
Hello all,
I have a question about possible interchangeability between an Oldmobile 3 point mount and a Chevrolet engine. Would be a temporary kind deal, but I'm curious if there are engine mounts for a Chevrolet block that would bolt onto the Olds front crossmember/mount? At the time I was...
This is my first time using a 3 point mount. I'm having trouble getting the yoke to slide on to the splines of the shaft. I have the rear mount bolted to the back of the engine with the u-joint assembly bolted to the PTO. I'm trying to lower the engine in and slide the yoke onto the pump shaft...
3 point mount taken out of my Eliminator. Mounts are in good shape stringer portion appears to have a slight bend not sure how important this is. $200 plus ride
standard deck mallory dual point with tach drive everything works and looks new had it for years and never ran it mouzer will bust my balls with the forum rules so $200 OBO infuses on the OBO
******UMPBA Drags Races Stevens Point WI Aug 20th******
UMPBA will hold 1000' drags Aug 20th at Bullheads Bar and Grill/ Rivers Edge Campground.
Races are scheduled to start at 11AM and run until 6PM or when all classes completed
The race site is located just a few miles north of the city...
I have a 21 ultra upen bow. Starting to order parts, thinking a big nick aka 598 bbc pump gas deal. The boat does not have a rail kit in it. What do you guys think?
Wtb 4 point motor mount for jet boat bbc 454
WTB 4 POINT MOTOR MOUNT FOR JET BOAT
looking for a glenwood style
i need only the rear, but will entertain both.
please let me know what you have.
bbc 454
Greg , first off thanks for the motor placement help . Now I'm having intake reset (leaked ) and I want to go with a back cut shoe to try and get ass of boat to lift and free up (as prior conversations it was breaking water about 4' from rear as you can see in my avitar ) . Had a tapered shoe in...