Performance Boats Forum banner

pull

  1. need to pull engine, what to expect with velvet drive?

    V-Drives
    Need to go through the engine, so it has to come out. Its currently behind a velvet drive, what should I expect while pulling it? No torque converter, drive flange should be mounted to the flywheel? Is it easiest to just unbolt the engine from the bell housing, and leave the bell housing and...
  2. How to pull olds 455 out

    Jet Boats
    Just wondering if it's as easy as it looks. I have what I believe is a 16' sidewinder SS with an olds 455 and Berkley 12jgb jet. It looks like I need to remove the bolts that go through the front cross-member, unbolt the driveshaft from the flywheel. What i am not sure about is do I unbolt...
  3. [Question] 17' 3" Hurricane steering pull

    V-Drives
    Hello; I just finished building a wood Bob Warren's Hurricane. When holding the steering wheel there is hardly any feel of a pull to the right, but when you let go of the wheel the boat wants to make a hard right. I have a large aluminum fin pointed straight ahead, left hand 3 blade prop...
  4. Stainless pull up cleats 6 Total

    Parts for Sale
    Six SS pull up cleats for sale. with backing plates stay in the down position until you pull up.Aprox 5 inch long X 1 inch wide. All six for 85.00 352 266 1457 0r [email protected]
  5. Engine trying to die after hard pull

    Jet Boats
    I just installed an Aeromotive electric fuel pump for mySJ. Pump is rated for over a 1000 HP. It's on a 505 BBC with a 1050 Proformcarb (1/2" line). I have it regulated down to 8 PSI. I think the motormakes around 600 to 630 HP. Coming in to the dock, I ran it 4k for a few minsand went to around...
  6. Engine **WANTED** Pontiac Engine V-Drive Pull Out

    Parts for Sale
    Someone must have one of these that they are swapping out for a BBC or BBF?!? Looking for a complete pull out or parts to throw one in a V Drive. Willing to pay for crating/arrange shipping
  7. 1500hp misc. Dyno pull @ boostpower marine

    GN7 On the Dyno
    Here is a misc. dyno run. Enjoy! DYNO PULL 1500 HORSEPOWER AT BOOSTPOWER.COM - YouTube
  8. Please help....need a push pull cable made ASAP in SoCal.

    V-Drives
    Trying to make the show in needles this weekend. All is done except the fuel shutoff. Anyone know of a local place where I can get the cable made. I am in Ontario Ca. Need the cable with the button in the middle for use with an enderle system Thanks, Dave
  9. WTB Pull Type Throttle Pedal

    Parts for Sale
    Well, now that I think about it, maybe no one makes a heel pivot. See what you got. I am positive that someone has one of these laying around!! Thanks, Keith
  10. push pull cable vs. cable and pulley steering

    V-Drives
    Pros and cons? Have a 70 Sanger with push pull steering.trying to build an 80-100 mph boat. Is this steering set up sufficient or do I need to change over? Much thanks!
  11. Will a 1/2 ton Chevy pull a 25'-28' deck boat adequately?

    PB Open Water
    I need answers. In particular at the launch ramp.
  12. ???inflatable pull tube???

    PB Open Water
    So im taking all my nephews and there friends to the river in a couple weeks and im gonna go buy a new tube to pull behind the boat. So i thought i would throw it up here and see if you guys have any recomendations on what to buy. I like flat tubes and hauling ass but the kids dont share my...
  13. where to pull oil temp on 460

    GN7 On the Dyno
    I want to install an oil temp senser on a 460. wheres a good place thats gonna get a good reading . theres a port beside the fuel pump block off plate. I'm thinkin good flow being close to filter
  14. Stainless Pull Up Cleats

    Parts for Sale
    Set of four Accon Slimline 6" Pull UP Cleats. Brand new, shipped to you in the CONUS for $110.00, that is half price folks! Stainless nuts and backing plates included. US Post Office Money Order accepted, or if you prefer PayPal please send as a gift or add 3% if you call it something else...
  15. Is This 496 Dyno Pull Legit?

    PB Open Water
    My buddy saw this in a youtube video, think its legitimate? I’m looking to upgrade, do you think this is a good system? Anybody recognize this guy, or the company? What about the exhaust, any good? Click on it and see what you think.
  16. [For Sale] 28' competetive enclosed (bumper pull)

    Trailers and Trailer Parts
    1990 3 axle enclosed trailer has 2 new axles (because its was cheaper to buy 2 than rebuild them) white in color, tires are decent, floor has d-ring hold downs I will post pics just getting the word out asking $4000 obo
  17. So the next time you go to the dyno, you might want to try this: 10 min pull

    GN7 On the Dyno
    When I was at Desert Storm a couple weeks ago one of the Merc reps told me to look for this video on his blog: Blog | Mercury Racing Wow. S CP :)grn
  18. Need to pull my motor

    Outdrives
    Gonna do some work on my motor. i have pulled plenty of car an jet boat motors but i have never from a stern drive. Does anyone have a detail on how the motor mounts to a bravo 1 and any tips or procedures on removing? thanks
  19. Can you pull a wisdom tooth?

    PB Open Water
    This is what the caller asked after I answered the phone, "Montgomery Cranes". I said sure, but using a crane to pull a tooth is a little over kill don't ya think!
  20. Ever pull a dizzy.....

    GN7 On the Dyno
    and hear a couple klinks then something roll in the pan.:|err
Top