Performance Boats Forum banner

pulling

  1. can you check cam timing without pulling the head

    GN7 On the Dyno
    I have a 468 bbc with brodix 2x heads,jesel belt drive the motor has a 728 lift crane solid roller cam with 7-4 swap, here is what happened I had a oil leak on the jesel seal behind the top gear so I fixed I but my motor never ran right since so I think I have it off a little when I run it up on...
  2. 07 Nissan titan pulling a 32ft baja

    Tow Vehicles
    What do y'all think about a 2007 nissan titan 2WD pulling a baja 32 caliber. The boat weighs 7000# dry with no trailer and my truck is rated to pull 9400#. My truck has the tow package and the factory hitch. How will my truck do pulling this? Will my hitch be up for the task? Will 2WD be a...
  3. Pulling the boat off the trailer

    V-Drives
    My new project needs some paint work on both the boat and trailer . I wanted to know the best way to separate the two in the garage . How to support the flatbottom correctly while still being able to paint most of the bottom.
  4. Pulling side pins and water hose?

    Outdrives
    Hey guys how do i get to the water hose? Does it take a Merc tool to pull side pins? And in the center of the hose looks like plastic holding it in? Does that unscrew?? Trying to just replace the water hose. Thank you
  5. What to look for, pulling the pan off a PCM 454

    GN7 On the Dyno
    Just bought a used late 80's vintage Supra with the PCM 454 330hp. I'm switching the drive train from typical tourny boat inboard to a v drive set up using a BW 72C with BW direct bolt up V drive so that I can use the existing shaft location/strut etc. I have also purchased a V drive oil pan...
  6. Pulling jet boat motor

    Jet Boats
    I need to pull the motor out of my new to me 1975 Weirdt Stinger to replace a oil pan gasket. 460 Ford with Berkley Jet. It looks pretty straight forward to me but I have never pulled the motor on a jet boat. My question is how the motor connects to the jet. I see what looks like a main...
  7. Help on pulling my intake

    Jet Boats
    1981 miller, now i got my motor and pump out but now the hard part, how do i get the intake out...........:confused:
  8. how about an E85 v6 pulling your toy hauler?

    GN7 On the Dyno
    stumbled across this....it's actually a little old, but man....its about time someone used this stuff like it should be used!
  9. Hooray ! Obama is pulling all troops out of Iraq !

    Political Rhetoric
    :))THumbsUp All troops out by 12/31/11 !! Finally! About time! Great news! Obama is starting to make good decisions! I see the pinhead Republicans are pouting about it...what fucking losers! :rolleyes:
  10. Pulling 5.7.............

    PB Open Water
    so im about to order the stuff to do my exhaust and a local guy says i have to pull the motor to put the block off plate on, is this true........:mad:
  11. Pulling boat out of water

    Jet Boats
    Anyone use any type of ATV to put boat(19') in and out of water? Rhino, artic, ranger. Quad, Brute force? Would a Brute force work? Don't want to break camp with the moho every night.:|err wifey no likey.
  12. can I remove my flywheel w/o pulling the motor

    Jet Boats
    I have a 21 ultra stealth w/Indmar 502 and a legend jet. There are 3-4 teeth missing on the flywheel and occassionally the motor stops just there so it wont crank w/o turning the harmonic balancer by hand. Can I remove the flywheel inside the boat or does the motor have to be pulled? The boat...
  13. Pulling heads. Do you replace the head bolts?

    GN7 On the Dyno
    Pulling heads. Do you replace the head bolts? UPDATE pg. 2 Subject says it all.. SBC 350. engine runs great so i want to eliminate the possibility of a head gasket on backwards or some other blocakge. Easy enough to pull the heads and put new gaskets in.. ' Do you reuse the old bolts or...
  14. pulling and resetting intake???

    Jet Boats
    I know there is probably an old forrum on resetting an intake. My intake came loose this summer so I need to fix it and have never done one. The pump was set back and has Ervin Capps speed bump that covers the front part of the intake. I've talked to Ervin about it and he can help over the...
  15. Warm bowl after pulling out of the water?

    Jet Boats
    Hey guys, I'm very new to the game here. When I pulled my boat out of the water last night I noticed the pump bowl was pretty warm to the touch. Is this normal or could the bushing be toast and I'm damaging the shaft if I keep using it? I checked the gear lube in it and the level is...
  16. SX fans what are the chances of K-Dub pulling it off???

    PB Open Water
    K-Dub is down by 16 points and Reed is injured. It's a long shot but I hope he gets it.
  17. I'm pulling a SKOM

    West Coast - South
    Headed out to Saguaro. All got to do's are kinda done and its hot outside. Good time to go to the lake.
Top