Search Results for ‘rear’

Looking for some inspiration in determining the position of the exhaust/muffler setup for 22 ft boat the BBC + turbo (under hatch) is fitted off the transom with inline Z-drive, crash gearbox behind motor the rear deck/cap slopes down to transom as the hatch is off the transom approx. 24", was...

I bought this nice aluminum fuel tank a couple of years ago from Dave Sammons but never used it. After installing it in my shallow side board GN (El Cid) hull it was just too tall and didn't look right. So it's up for sale. Measurements are 22" tall 35" wide and 18" front to back. According to...

Pro's and cons on which end to point forward? Thanks!

Selling a 12 bolt GM complete rear end. Moser axles 410 gears inside of rear spotless. Asking $1850.00 Removed from 70 Chevelle SS

New 6061 Billet Mercury Verado Rear motor Mounts and 316SS Wing Plate for Rear Tie Bar set Up.

BB chevy Had as a spare nice condition asking 45.00 obo see width.

Brand new high performance CNC cut rear tie bar mounting kit for the 250-400r Verados, tie bar not included. Wing plates come standard with Go-Pro camera mounts and life time full replacement warranty on motor mount bushings. Call or text for any questions or details 252-646-2751.

found one, Rear Engine plate found one, no need for plate now Looking for a Rear Engine plate 22 X 3/8" Please Call 530 575 5025

Wondering if anyone in SE Michigan has a rear engine mount for BBF? I need the 4 point style. It's going in a Spectra 20 with a berkeley jet. Also looking for a rear sump 460 jet pan.

all aluminum. shreveport, louisiana 318-687-9088 or 318-470-1482 all the plates and transom plate-$140 Have a nice 572 pump gas motor with only 20 hours on it in a 22 ft eliminator daytona inboard outboard boat. It has a 10.2 merlin 2 block, je blower pistons with 9.7-1 compression, ohio...

Want to buy fiberglass rear bench seat. Needs to be between 56 and 58.5 inches wide. Let me know what you have, thanks

Rear mount 460 Ford- Price Reduced 3/8" thick aluminum plate, 6061. for 164 tooth flywheel, includes fabricated flywheel cover. Fits between 26" spaced stringers. Drive line cover locater is 5" dia. $125.00 plus shipping.

Looking for any type rear seating for a 19' Howard V-drive. Just need rear seating to put in till I see if I am going to keep the boat, nothing fancy. Pm or Call/text if you have anything. Thanks Johnf 4083403692

Borla part # 11856 Brand new in box...Check part number for details $1800obo plus ride

Re doing my boat and removed the cocktail seating and replaced with front buckets ...... Looking for a nice rear fiberglass bench seat going in a 19' CP. Any suggestions and pics would be greatly appreciated. Thanks in advance

What do you guys use for a anchor on the sand or beach when you have the boat turned facing out? Here on the river the sand bars are all soft sand and nothing likes to hold. Any suggestions

Never installed into my truck. 13.5 ring gear. 14 bolt. 3:73 ratio. $800.00

Throwing this out there if anyone can use them. 67-81 Camaro 68-79 nova Hotchkis Sport leaf spring kit. will lower car approx 1.5 inchs.. also have QA1 rear shocks .. will sell everything for $450.00. price it out Leafs are 450 and shocks are 145 each ...

I am looking for ready to bolt in BBC motor mounts front and rear. They need need to be pretty I will polish then. Just need to get motor in boat and not have to sell my left nut for them.

WTB Mopar/Chrysler rear engine mount cast or rail type Tom 844 816 1845