Performance Boats Forum banner
1-20 of 41 Results
  1. PB Open Water
    I have a Gen V 454 that I'm getting ready to place back in my 1996 Mirage Jaguar Jet boat. The engine is stock from everything that I know about it. I just placed a new Edlebrock Victor Jr. high rise open plenum intake on it. I'm looking to put a new carb on it. I have an older Holley 750CFM...
  2. GN7 On the Dyno
    BBC 468, 12.7-1, Pro Comp 3021 heads, approx. 650+hp. Street use, a NGK R5671A-7 or equivalent is recommended. Thinking I need a little colder. Any suggestions
  3. GN7 On the Dyno
    468 BBC, 12.9-1 compression, full roller. Pro Comp aluminum heads. Ran Champion 263 with iron heads.
  4. Bob Teague
    I have put a 300 "Tempest" Mercruiser SBC w/ a B&M 144 Supercharger, in my 1987 21ft chris craft scorpion 210 limited boat. And i might want to go to a SBC 400 or go ahead and put a BBC Mercruiser 502 "bulldog "in the boat. The outdrive is a Alpha 1 gen 1 drive and im sure with the "Tempest"...
  5. V-Drives
    So after enough years I'm finally going to upgrade the prop. What would you recommend for a 21ft Howard with a standard LS-6 BBC? Champion V-drive and a 1" shaft. We ski a lot and don't really run all out often but will occasionally. Anybody have a recommendation of have one that would work?
  6. Jet Boats
    My jet has a stock 454 (no engine cover)....Would this be a wise choice? Better choice(s)? Street Fire Chevrolet V8 GM HEI Distributor - 8362
  7. Mideast and Great Lakes
    Hello all, Brand new here and to boats in general. I have been into performance cars so far my entire life, and always had the itch for a boat, but never got into it. Growing up my father had a bunch of boats, and recently talking with him got me interested in wanting one for myself. I am quite...
  8. GN7 On the Dyno
    Still working on the Hallet. Have decided a cam and possible intake change are in order. Could I get some experienced advice on the best choices for my application? Motor is 8.25 CR, Dove heads with stock sized valves and some porting, 950 cfm professionally set up Holley, running 30 degrees...
  9. Jet Boats
    My Prestolite starter requires a ford style remote solenoid so I thought I would check in and see what is absolutely the best brand to go with in a marine environment. What should I be looking for amp wise, etc?
  10. Jet Boats
    Looking for some recommendations on fuel level senders that don't cost more than my carb:rolleyes: I have twin 13 gallon tanks and one gauge. Are there any quality "universal" senders on the market that won't break my back? Something in the $20-$40 range?
  11. V-Drives
    Wondering what would be a good spark plug for blown gas 489 ci. BBC was running auto lite 26 in the old aspirated set up probably kneed to go cooler. So whata ya runnin?:hmmm:
  12. Jet Boats
    Hey guys i need some help. I have a mild build 454 with speed pro hyper pistons, comp cam extreme marine cam kit. The eninge is done being rebuilt and the bearing clearences are on the looser side. Right now I have a stock oil pan and a HV melling oil pump. Am I asking for trouble? Should I...
  13. GN7 On the Dyno
    The engine has a Merlin II block with 4.5 bore. The block has been O-ring (height is .010 with a bore of 4.78).
  14. GN7 On the Dyno
    I need some help choosing the right oil pump and pickup for my Milodon oil pan with windage tray. It's a 10qt pan and with this new motor I want something that gives me constant oil pressure and also trying to figure out what I should do ask far as pan evac or catch can. From reading past...
  15. GN7 On the Dyno
    Hi, I have an engine which I Purchased and never got cam specs or card with. It has been running very well but time to check the rockers and I am not exactly sure what to set the lash at, Without going to the lengths of pulling the cam and finding out specs. Currently I have some up and down...
  16. PB Open Water
    Looking for a good transmission rebuilder in OC area. Chevy 4L60e out of a 2001 Silverado 1500 4x4 with 5.3. I will drop the trans off and pick up after rebuild. Thanks!
  17. Jet Boats
    Looking for a inexpensive oil with high ZDDP (zinc) rating since I'm running a basically stock motor with a flat tappet hydraulic cam. I found Castrol Edge 5w50 has 1300, but it's close to $10 a quart, that's $100 in oil! If I would like to find something in the $5 range. I can live with that...
  18. GN7 On the Dyno
    I will soon be reassembling a turbo intercooler for a Race Aero Turbo. Is there a gasket material that is recommended for doing that? Fel Pro makes several gasket material sheets that would appear to work. One is cork/rubber material and another is a roll of what appears to be similar to a...
  19. GN7 On the Dyno
    We are assembling a new 540 blown efi engine and need help with head gasket selection. We will be putting it in a 21' Raysoncraft. We plan to keep it mild and on pump gas. It will be a river cruiser. Here's the basics; Dart block with extra head bolt option, not "o ringed". Brodix heads...
  20. Outboards
    I am in Huntington Beach and I want to get the 100 hour service done on my 300XS. Anyone out there know a trustworthy outboard specialist to service it?
1-20 of 41 Results