Search Results for ‘roller’

Hey guys! Anybody know what year Chevy small blocks started going roller? I am on the hunt for a roller block for a build I will be doing for a 4x4

Took these lifters out of a good running lake boat with small cam. They are in great shape. in shreveport, louisiana 318-470-1482

Looking to replace my flat tappet with a retro fit roller kit. Is it worth it to convert over to a roller setup? Anyone recommend a complete kit for a Gen IV BBC 454?

brand new bbc lifters in shreveport, louisiana 318-470-1482

So who's lifters are the shindizzle?

On older gen small and big block chevys, what options do I have for setting roller cam end play when using a neovane water pump. I thought I read somewhere that the neovane won't stand up to it but I can't find that article either. Chris

Cam Style: Mechanical roller tappet Basic Operating RPM Range: 3,000-7,000 Intake Duration at 050 inch Lift: 249 Exhaust Duration at 050 inch Lift: 255 Duration at 050 inch Lift: 249 int./255 exh. Advertised Intake Duration: 281 Advertised Exhaust Duration: 287 Advertised Duration: 281...

Set of 16 used but in great shape BBC Harland Roller Rocker arms with Standard size Poly Locks. will need taller locks if you use Stud girdles. selling all 16 with Brand new in the bag Poly Locks 160.00.. 530-333-1047 Located Near Sacramento

Pump gas 4 bolt 496. Scat bottom end with probe pistons, REC port open alum heads from RHS with stainless valves and a Howard cam shaft. PRM roller lifters and Crower stainless rockers. Jet pan. I will try a get the pan off tomorrow for inspection. Short block has approximately 10...

I bought a boat recently that had this 468 in it. I witnessed it run on my local lake all summer and it sounded really good so I bought it when the owner ran into some money problems. The owner had it freshened 2 seasons ago with rings and bearings and did a valve job. According to owner it...

I bought a boat recently that had this 468 in it. I witnessed it run on my local lake all summer and it sounded really good so I bought it when the owner ran into some money problems. The owner had it freshened 2 seasons ago with rings and bearings and did a valve job. According to owner it...

(SOLD) BBC roller rockers by comp cams... For sale is a set of like brand new COMP CAM 1620-16 Ultra pro Magnum Rocker Arms. They are 7/16in. Ratio 1.7in Chevy Big Block 396-454 cid full set of 16. They're from summit racing $333.83 on line. I will take $225 shipped to your door! Any ?s call me...

I have a full set of like new Comp Solid roller lifters for sale. They are part #866-16 .842 dia and .300 long. $300.00 OBO shipped in the 48 states. contact me via e-mail please. Jim [email protected]

I have a brand new set of PAC #1224 solid roller springs. They were purchased on a brand new set of AFR 2101 heads that are being used with a hydraulic roller cam. They are $310 from Summit, buy this set for $225 Here is the Summit listing with all specs...

On my BBC comp cam hydraulic roller lifters I preloaded them 1/2 turn, they are a little noisy, mostly at idle, which from what I have read can be normal. Would going to 3/4 or 1 full turn be advised?

I have a used set of Comp Solid roller lifters .842 part #866-16 with only 4 dyno pull's on them they are like new. $300.00 plus the ride. Jim Sampica 602-448-9374

Hi, I have two BBC solid roller cams as one was installed but never ran and the other one is used. The cam cards are below for review and PM me to work out the detail as I am asking $200 OBO for the new one and $150 for the used one. Thanks

515 ci, 13:1, hyd. roller, 893 hp @ 7100. Heads and intake by Foxwell, cam by Straub, engine built and dyno'd by Mark Jones "Vortecpro".

I know for flat tappet you break the cam in and immediately change the oil. What do you guys do for hydraulic roller?

Set of PBM hydraulic roller lifters. I never ran them. Bought them for a project but decided to skip the roller cam upgrade this year and just go with another flat tappet. I'm pretty sure that the guy I bought them from said they had about 120 hours on them but who knows. From what I can see...