Performance Boats Forum banner
1-20 of 32 Results
  1. Outdrives
    Hello all, So we have a 1977 GM Ranger runabout. Cleaned it up and took it out for the first time sence buying it. Runs great. But. At first it shifted into forward just fine. But after running it for about a half hour, it started not shifting into reverse from neutral until half way to WOT...
  2. Parts for Sale
    Looking for a "Hondo" stamped vdrive shift handle...Please PM me if ya have one you are willing to part with...Thanks for your time
  3. PB Open Water
    So i have 85 chris craft scorpion ltd w/ alpha1 gen1 drive, 300 tempest MerCrusier motor and has a 144 b&M supercharger on it. The motor had some issue's last year with vacuum leaks and what i thought might be the distributor which was the stock merc thunderbolt IV. i fixed the leaks and...
  4. Parts for Sale
    2 Vintage handles one used Hondo in good shape could use polish The Hall Craft was bought as new and was used on a V-Drive that was siting on a shelf casting on one side is poor $100.00 plus shipping Call Tim 508-902-8528
  5. User "How To" Section
    I took my 1988 Formula 206LS out for the first time this weekend (the only time before I have to winterize). The boat has a carbureted mercury 350 Magnum. Everything ran great in the beginning but eventually I was unable to shift into neutral. The control was very difficult to move and would...
  6. PB Open Water
    I would like to cleanup my home built Quadrotor engine by relocating the shift linkage off the CMI's, does someone make a bracket? And where have some of you put it? I assume you can only, really swing it to the transom on the starboard side, but I feel swimmers getting in will dump water on it...
  7. Parts for Sale
    looking for a manual shift handle for a 10 disk lenco clutch. thanx Gerry
  8. Outdrives
    merc alpha 1 shift cable boot replacement advise/help A pal has a mariah b.r. skiboat thats in need of the shift cable boot replaced and i volunteered(gtn payed) to replace it.ive done nothing but glance at it so far and if the cable can be taken loose from outdrive easily it looks pretty...
  9. Outdrives
    I have an 1987 OMC Cobra stern drive with a 5.7L that will not shift back to neutral the first time when put in water. After I get it in neutral it will shift fine the rest of the day. Any ideas what might be the problem. Thanks
  10. V-Drives
    gentlemen,can someone tell me how to plumb a lenco? never ran one and i know you guys are expert in this field,help is greatly appreciated;
  11. Parts for Sale
    Looking for an jet shift lever assembly. Converting from a throttle/shifter combo. Will consider trading the combo if you want to convert the other way. Also looking for a tapered shaft steering hub with three bolt grant pattern. Thanks -Ricky 602-370-4074
  12. Parts for Sale
    i need a mercruiser 496 dts shift bracket assembley less the actuator
  13. Parts for Sale
    I need a locking shift handle in good condition for my Casale 10* split case. Please reply if you have one for sale that you don't need any more. 208-409-7911
  14. Parts for Sale
    Need the arm for an air shifter on the v drive.It's the splined piece and want it in good shape. Needed immediately thank you
  15. Parts for Sale
    I bought these for my project but I never used. My loss your gain... Brand New Throttle and Shift for Single Engine (similar to Livorsi)- $500
  16. Parts for Sale
    I just bought this and it doesn't fit in my dash and I don't want to bore out the hole. So, its up for sale. Used Autometer Autogauge 5" Monster Tach 10K rpm with external shift light. In good shape and I made sure it works. I paid $60 so that's all I'm asking for plus the ride. Figure USPS flat...
  17. Outdrives
    My electric shift stopped working & I have no idea where to start. I have a complete spare complete engine & lower unit that I know works. When I switched lower units, same thing. Any ideas? It's gotta be an electric problem!!! Mel
  18. Parts for Sale
    Brand new...never installed complete v-drive air shift kit.....300 to your door!
  19. Outdrives
    i swapped out a v6 mercruiser which is a 1987 to a chevy 350 i am running a automotive style gm hei the shift interupter switch that comes stock works oppsite of what i need has i cant be the only one who has ever run into this issue so if anybody knows what to do or where to get the proper...
  20. V-Drives
    Looking for in/out shift handle for a casale v-drive
1-20 of 32 Results