Performance Boats Forum banner

speed

  1. Jet Boats
    I have a 19 Coumbian boat with panther jet. Just wonder what top speed should its powered by the amc 360. 4200, 4500 rpm
  2. Parts for Sale
    B&J two speed 10 spine button-16 spine drive shaft-30 split $1,000 6one8-567-one804
  3. V-Drives
    I bought this boat several years ago, and the previous owner did not have a lot of information on the hull itself. I and am looking for more information on the hull style (Maybe the model info), as well as suggestions for a cover. As far as I know, this is a 1980 Marlin speed boat, I cannot...
  4. Boats for Sale
    454 Big Block Chevy, Bored 60 over, 10.5 flat top pistons, roller cam, mark 5 heads, 13 qt oil pan, dominator intake (single plane), 850 Holley with duel feed & double pumper, high torque starter, mega pump (water pump), steel crank, adjustable 2 piece cavitation plate with pedal and lock-out...
  5. Parts for Sale
    For sale Steel speed rudder. HallCraft Quadrant. overall 22", 10 "X 1" shaft. $200 plus shipping. part is in Panama City, Florida.
  6. Parts for Sale
    Owens Racing 2 speed transmission I have for sale an Owens 2 speed transmission. It is a triple sprag, 30 split trans. It was just inspected and rebuilt with a new clutch pack, new sprag races, and fresh sprags. Just add oil and it's ready to go. It is mechanically in excellent condition, and...
  7. Jet Boats
    18 ft Sanger superjet 1977 I am the original owner of a 18ft 1977 sanger super jet and I like it. Last year the floor and foam were removed, replaced and glassed stronger than new (delta pad.) The hull under, was in like new condition and outside no stress cracks anywhere. I know i will never...
  8. Parts for Sale
    Have a 2 speed fresh from Owens 30 split. $900.00
  9. Parts for Sale
    Custom made Low High speed jet log.
  10. Parts for Sale
    B&J 2 speed trans B&J two speed 10 spine button-16 spine drive shaft-30 split $1,200 618-567-1804
  11. Parts for Sale
    Owens 2 speed sprag transmission 30% split. $1100 Obo located in Stockton CA 95215
  12. Jet Boats
    Hello, Im new to the forum and looking for some advice. I have a Jetboat with a berkeley pump. lets say hypothetically my peek engine HP on a dyno is at 4700 RPM even though the engine is capable of turning 5500-6000 safely, would it be better to set my pump/boat up to top out at around 4700 RMP...
  13. Greg Shoemaker
    Greg, This is the video that has the drive live speed changing because the yoke angles are different. We talked about this this weekend at Ming. I don't remember where I had originally seen this. I believe it was posted here in PB? https://www.youtube.com/watch?v=gmV4qwLfOMY Be safe, schick
  14. Tow Vehicles, Cars and Parts
    2004 Mustang GT Conv AUTO Trans Parting out or whole car 1250.00 have a 2004 Mustang GT Conv with a 4.6 and a AUTO trans. car was wrecked and rolled. the front is junk but the driver door and qtr panel, trunk&Spoiler, rear bumper, tail lights and cONV tOP STILL IN GOOD SHAPE. THE ENGINE TRANS...
  15. Parts for Sale
    Hello all, I have a set of L2399 Speed Pro BBC Pistons for Mark IV Chevrolet BBC. They are +0.060". I have 8 Pistons that ran for a pretty short period of time in an engine that let go of some valves. So, there are some dings on the tops. My engine guy checked them out and said that they...
  16. West Coast - South
    Does anyone know Mike at MK Hammer Speed and Marine in San Bernardino or how to get in touch with him? He hasn't answered his business phone in over a week. He's building a motor for me and I've been in constant contact with him for months so I'm wondering if something is wrong.........
  17. GN7 On the Dyno
    Does anyone know Mike at MK Hammer Speed and Marine in San Bernardino or how to get in touch with him? He hasn't answered his business phone in over a week. He's building a motor for me and I've been in constant contact with him for months so I'm wondering if something is wrong.........
  18. PB Open Water
    Does anyone know Mike at MK Hammer Speed and Marine in San Bernardino or how to get in touch with him? He hasn't answered his business phone in over a week. He's building a motor for me and I've been in constant contact with him for months so I'm wondering if something is wrong.........
  19. Jet Boats
    This question has probably been asked and answered 100 times on here but could not find any old threads... But is there benefits or down falls of speed coating the inside of my bowl and my impeller.?My intake and loader have already been done.
Top