Search Results for ‘starter’

Have very nice RCD front crankshaft aircraft style starter with cable, solenoid and starter dog jaw and spacer. $1800.00 [email protected]

Hello, I have a 20' speed boat with a BB Chevy ( 454 stroker) jet drive and the motor is in the open meaning it is NOT covered. The starter needs to be replaced, so, do I need to purchase a marine starter or will a regular automotive high torque mini starter do? I am aware that the marine...

well just to update,, i had to lift the motor which was actually a little bit of a pain in the ass but not to bad,,,,and was able to get the starter in,,,,i meassured for clearances the best i could ,,,i put some greese on the starter gear and i engaged the starter with some juice from the...

well i got the starter and man that thing is light! looks awesome only problem is it doesnt fit!!!:((((((,,,,to clarify the front mounting block of the new starter is wider than the original starters, the mounting bolts are longer and now I cant even get a bolt started in the hole of the block...

Mornin', I've never dealt with one of these before so any tips are appreciated. Boat has a newer engine and I suspect it's been cranked over some extra spins due to a poorly functioning choke on carb. Having the starter freshened up and wondered if they need to be set up or shimmed for...

I have an 84 Webbcraft Dynasty with the original 350 Chevrolet engine, I took the starter off the other day to have it rebuilt and have a question about the wiring on the starter solenoid. There is a brass or copper connector bolted to the solenoid where the main battery cable attaches and the...

new arp head studs, leash timer, end yoke Brand new set of arp head studs for brodix aluminum blocks with dart pro one or 360 style heads. Summit price is $319. - $185. Brand new 1350 series spicer driveshaft end yoke that fits the jetaway. Comes with new strap kit. Summit was $175 with...

Have a fresh from Owens 2 speed 30 split sprag type transmission $1000.00 obo

Precision Power, Inc. Top mount starter. $50 plus shipping. Item is located in Reading, MI.

Starter, Mini Alt. etc. Reveres rotation HP Delco PG20M Powder coated starter never used $200.00. Used powder coated Mini Alt. $100.00. New Mercury steering pump $100.00. Everything is in Parker Az. or can bring back to SoCal if needed. Shipping is extra. Thank You, Bobby (805) 432-5738

Summit BBC gear reduction starter. Works great, will not fit my new oil pan. Located in Carson City NV. $45.00 plus shipping

This is a 1.4 hp planetary style gear reduction starter for sbc and bbc. It is not for high compression. in shreveport, la. 318-687-9088 or 318-470-1482 $85

454 says berkely 454-2 which I assume means 2 bolt. I took it out of my last boat before I sold it, the last time I had it out it ran great with good oil pressure and rpm's around 4600 with logs and A impeller. There is some surface rust in exhaust ports, either from the exhaust I ran on the...

SOLD BBC High torque starter SOLD Big block chevy high torque starter $75.00

0 can anyboy tellme how to wire a min sttarter o my 460 ford jet boat I have a unilite distributor . I orginaly had 4 wires main battey cable and large guage red wire go together on the batt terminal white wire to "S" terminal and orange wire to " R" terminal. now only 2 terminals. where do...

Looking for a top mount starter setup for BBC Thanks, Todd

New, never used or bolted on Tilton Severe Duty starter. #54-40001. BBC unit for 153 or 168 tooth flywheel. Comes in original box. Was carried around in our race trailer as a spare. $175.00 plus USPS shipping.

BBC and I have a lifetime warranty autozone starter. I usually have to replace yearly, which is getting old. Yesterday, I noticed that if I run the boat for say ten mins then shut it off and try to crank it back up, the starter is starting to drag. I have the bell housing that is set up for a...

Starter fresh rebuilt Autolite A3510S $25 plus shipping Alternator fresh rebuilt 55 amp One Wire $25 plus shipping

Is there an issue with using one of those GM Trans Spacer and a standard cast iron nose starters? I had to grind some of the nose of the starter just to get the bolts started. I think it put pressure in the starter and it chewed up the bushing and housing itself in just two outings.