Performance Boats Forum banner

Discussions Showcase Albums Media Media Comments Tags Marketplace

1-20 of 364 Results
  1. V-Drives
    Hey folks, Have to replace the aluminum whip strut and steering plates in my 1959 Beisemeyer and in the process I broke a sheave (bearings fell out of it). Aprox 4" for cable steering. Any help?
  2. V-Drives
    just had another stupid question,,,im replacing my steering shaft and gear ,,in the process i decided to replace the sleeve in my steering post,,,,its old really old probably late 60's early 70's and it had what i thought was a brass sleeve so i ordered some oillite brass/bronze sleeves and...
  3. Parts for Sale
    10" Polished Glenwood Steering post, mounted but never used. $150.00 plus ride
  4. Parts for Sale
    Brand New Place Diverter Trim Switch Brand new comes with everything you see here. $50 plus shipping.
  5. Parts for Sale
    looking for a 10" steering post straight cut. thanks! Sheldon
  6. Parts for Sale
    Sold! Steering Wheels All are Sold.
  7. Parts for Sale
    Jet ( teleflex) steering extension 9 1/2 inch. Custom machined by Dillon Munson from solid aluminum round stock. With hardware. $55 shipped 918 two six nine 8084
  8. PB Open Water
    I have a 1983 30ft Scarab S-Type w/twin 330 TRS outdrives. I am experiencing while driving at any speed on plane a condition where my steering veers on it's own either to the left or right. When I compensate to the opposite side it veers drastically to the other side & I cannot control the...
  9. Jet Boats
    Anyone know the diameter of the typical steering cable end (pump side)? It's the stainless rod that bolts to the nozzle. Thx
  10. Parts for Sale
    Hello fellow boaters found some parts I have when I had my advantage party cat it' a steering wheel with the hub, adapter is 3 3/8 deep $75 I am in Northridge will ship on your dime thanks for looking.pics available on request ,pics won't load.
  11. V-Drives
    What steering wheel does everyone use in a drag boat. I found two grant wheels I like but one is 11" and the other is 13". Thanks
  12. Parts for Sale
    Looking for a steering post and hub combination at least 8 3/4" in length. Bolt pattern doesn't matter as neither the dash or wheel are drilled yet. I'm using a 3/4" shaft from the hub to the shroeder box. Prefer no powder coat but lets see what's available. Bob 803 351 0578
  13. Parts for Sale
    new 10" wheel $60 shipped $50 local pick up new shifter $50 shipped $40 local pick up
  14. V-Drives
    Anyone run one on their small v-drive as opposed to the cable system? I am restoring a 18 sanger and have both set ups. Its going to be more of a cruiser than a drag boat. Any downside to the rack? Thanks
  15. PB Open Water
    So the Twin turbo setup I am putting in my boat wont fit unless I get rid of the power steering bracket and pump. So I want to go Full Hydraulic Steering. Which is the best brand? 1989 Checkmate Maxxum 229 with Bravo 1 outdrive. Thanks for the input. Jason
  16. Jet Boats
    I forgot to bring my old cable from the river and want to order a new one before I head back up. Does anyone know the cable length for this boat? Pump is set back with a snoot.
  17. Jet Boats
    I just got a 91 Advantage open bow 20.5. With it sitting on the trailer, the steering wheel can be turned from stop to stop with my little finger. Put it in the water and it like wrestling a bear. The pump is an American Turbine ATJ with trim. I ask because my last boat (78 Southwind) would...
  18. Parts for Sale
    3 COMPLETE SETS GOLD 3 PC SET $250.............sold 2 OTHER 3 PC SETS $100 EACH COLUMS RODS GEARS CABLE QUADRENTS AND LOTS OF EXTRAS....PROBABLY MORE THEN PICTURED TAKE IT ALL FOR $250 + SHIPPED TEXT IS BEST DONT ANSWER ALL THE TIME....NINE FIVE ONE 870-69 TEN ..MOUZER do NOT contact me...
  19. V-Drives
    I have a 10 inch post from the dash. I need 6 more inches for my driver to be comfortable in his driving position. Does anybody make 6 inch extensions that bolts up to our existing 10 inch post? Thank you for any help in this matter.
  20. V-Drives
    The last time I was at the lake the boat started pulling to the left, I was afraid that my skegs got bent because I was beaching the boat and after looking at them they do look a little bent , although after talking to some people about this I was told that they would have to be bent a shit load...
1-20 of 364 Results
Top