Performance Boats Forum banner
stick
1-15 of 16 Results
  1. Jet Boats
    Looking for a BBC dip stick that the knob/handle is the stopper (or screws in)into the oil pan I've seen them on other boats but when I ask where they got them everyone says it came with the boat so some one out here has to know where to get them or fab one up for me.Thanks
  2. V-Drives
    I am looking for and aftermarket dipstick similar to a LoKar shorty dipstick that will fir a Velvet Drive transmission with a 5/8" opening in the case. LoKar only makes 3/4" dipsticks. Anyone know of a product that might work? Thanks, Steve
  3. PB Open Water
    I like the idea of having a center throttle like the Baja Sidewinder or Scarab 23 SCS... Are there other "affordable" boats that have/had this setup? I believe some of the smaller CC Stinger's had this setup as well - although they did not have a true "pod" but just the throttle thrown in...
  4. Jet Boats
    How are you guys securing yous dipsticks? I bought one online 455 olds specific, Theres a lot of resistance when pulling out and putting in the dipstick, If I dont hold the mounting base while pulling the stick out it will pull the whole think out, when is a pain in the ass to line up and get...
  5. Jet Boats
    after running the boat for a while oil comes up from the dip stick .what could it be???its been doing this since i bought it its just a mess at the end of the day. 460 milled heads .baby cam..what could it be??
  6. GN7 On the Dyno
    :D seriously I need to braze it up. Does anyone think the oil will catch on fire with in the motor if I try to do it on the motor or should I take it off the motor? I`m planning on taking it off but just in case I can be lazy I figured I would ask? its a dooley steel pan if that...
  7. PB Open Water
    Who has it from the Springs. I know it's Dark Rum and Amaretto but what else?
  8. PB Open Water
    Wife loves those blended Big Stick drinks at Havasu Springs. Anyone know how to make them. I tried the Sloe Gin, Southern Comfort and Peach Schnapps recipe, but it just didn't taste the same.
  9. PB Open Water
    Should be an interesting day for Fannie. Looks like their earnings came in 3 times worse than analysts predicted, so today could mark an all-time low. Gonna be ugly. Looks like the band-aids are not working, what now?:|err
  10. Jet Boats
    Launched at Jack Smith on Friday and was cruising down river when the boat started cavitating and seemed to have lost power. Motor was still turning RPMs but could not do much more than idle. Wasnt sure what it was but thought it might have been something stuck in the impeller. Took the boat...
  11. PB Open Water
    Stick on decal and flames needed!!!! I just bought this from River Otter and I need to pimp out my new tow ride with some flames and such.... anyone know where I can get some???
  12. Paint and Fiberglass Repair
    I'm doing some trailer fender repair. The original wood was rotted- 7/16 x 4" x 7' strip ply. I would like to replace it with pressure treated but don't know if the fiberglass resin will bite to pressure treated plywood. Thanks for any feedback. I cleaned off the old rotted ply below, now down...
  13. PB Open Water
    Or, will they have a "hard" time sticking where they have been stuck!!! Just something that crossed my immature mind!!
  14. GN7 On the Dyno
    What makes more power an MSD with a digital 7 or a mag setup. I am currently running the mag but was offered to try out the MSD digital 7. What are the pros and cons? Has anyone ever dynod the two? Thanks.
  15. V-Drives
    I was just wondering what you do with the dipstickhole in your block since your dipstick on your v drive is in the pan. Do you just put a tube and dipstick on or is there a block off. Thanks.
1-15 of 16 Results
Top