Performance Boats Forum banner

Discussions Showcase Albums Media Media Comments Tags Marketplace

1-19 of 70 Results
  1. V-Drives
    Couldn't find any videos on how to do this. Figured I'd make one for those that have never done it..
  2. Parts for Sale
    Long beach swap meet this Sunday 9/9/18, If you need anything call me before 5pm today I'll bring it, I'ii be in row J spot 10 Jim 1818-890-1867
  3. Outdrives
    Does anyone know what the v- belt sizes are for the PS & Alt are when swapping the circulation pump out with a crossover system?
  4. Outdrives
    Is it an easy swap to replace a Gen IV Mercruiser Magnum 454 (1992) with a newer Gen V Mercruser 454 Bravo 3 365HP.
  5. GN7 On the Dyno
    I have a quick question.... I just swapped to a Hei and there is a wire coming from my altenator (yellow) that went to my 12volt side of ballast... Now that I ditched the ballast and coil, what do I do with the wire? Also what does the wire do? Im running a old school original Motorola marine...
  6. Parts for Sale
    swap meet sunday 1/29/17 call if you need anything, i'll be in row I space 26, 1818-890-1867
  7. Parts for Sale
    Im looking for a set of BBC exhaust logs with snails for a jet Im looking for the ones that run water along the top by the exhaust ports. I would be willing to buy or do a trade for a set of S.S. threw transom headers from BBC will include water lines and T valve.
  8. Jet Boats
    New guy, first post!! Long story short, I have a garage full of parts from previous projects including a complete running 4.8 out of an 05 express van. I always wanted a jet boat, and came across this engineless 79 Taylor SS. I went and got it a while back, brought it to a friends barn for...
  9. Parts for Sale
    I have a standard IMCO lower that was just rebuilt with 13 hours of use. Has IMCO shafts, 1" prop shaft, NEW MERC bearings and gears and is 1.5 ratio. I am looking to trade or a -2 IMCO with a 1.5 ratio and either size prop shaft is fine. E-mail or text [email protected] or 847-754-0335
  10. Parts for Sale
    I have a -2" Shorty IMCO 1.5 lower unit. It was just inspected and serviced in great condition. I would be interested in swapping for a standard length IMCO lower unit. I am only interested in trading and have no interest is selling. Located in Phoenix. Email for any info. [email protected]
  11. Jet Boats
    I have a 1976 Checkmate with 455 Olds and Berkly Jet, last refresh was 2001, and it has been sitting for just over 10 years now since last ran. I know the motor needs to come out and get rebuilt again. The motor has log manifolds with over the transom exhaust and is not family friendly for...
  12. Paint and Fiberglass Repair
    Hi Everyone.. I have a few questions for the Experts I have 2 Cee Bee Avengers, one (Red) is a 185 Model has windshield, covered engine compartment and higher sides Bad Floors and Stingers, needs deck repair in bow area, solid Intake original hull bottom Blue Model 175 i think Current Solid...
  13. Outdrives
    Guys, I'm looking at a 1979 26' day cruiser with a 454 and TRS drive. Not sure if the trans is B/W or MercTrans. Not being familiar with TRS, I took to Google and found a decent amount of info on random forums. It appears that while these configurations can be pretty bulletproof, finding...
  14. Parts for Sale
    long beach swapmeet this sunday, i'll be in row I spots 34 and 36
  15. Jet Boats
    Will a Place Diverter on a Berkeley like the one on the Brown Glastron fit on a Berkeley 12jc like the one on my Spectra ? :)eh:) The bowls look the same so I'm thinking it should be a go.:thumb:
  16. Bob Teague
    I have a Rinker 236 cuddy its 23ft it has a locked up 320 hp 454 in it my question is if it could be swapped out with a 230 hp 305?
  17. Jet Boats
    So I blew out one of the water ports on one of the heads on my boat. I don't know squat about the motor other than it's a 454. Found a motor/tranny combo local for cheap. Pulled the heads off and block, pistons cylinder walls look fine. So I'm thinking about just swapping the heads and manifold...
  18. V-Drives
    I recently purchased a 1975 mandella 20.5' mini daycruiser. Extremely clean boat but it does still have the original fiberglass tanks that run along the side of the boat from mid hull to about a foot off the transom. Still seem to be in good shape with no leaks or lamination or cracking. Heard...
  19. Bob Teague
    I have done quite a bit of searching here and am still looking for some answers. I need to know the cam specs for the production cam in my 1990 5.7 I have a new set of vortec 062 heads from GMPP, an intake i got @ swap meet. I want to use a set of comp 1.6 magnum rockers instead of a cam swap...
1-19 of 70 Results