Search Results for ‘switch’

Brand New Place Diverter Trim Switch Brand new comes with everything you see here. $50 plus shipping.

I am wanting to install an oil pressure safety switch for my fuel pump on my 454 BBC. How do I go about doing this? Do I use a T fitting and screw them both into the same port? Thanks for the help. If anyone has pictures that would be a huge help.

Looking into what you guys use for a kill switch I've used the chepo plastic ones w/ the wire spring and seems after a short period the cap keeps popping off or it breaks anything out there better pics would be a plus ,ready to buy if someone makes a good one.

Looking for one of these, let me know if you have one you would like to sell and how much you want for it shipped to 97055 (Oregon). Thanks, Chris

Aeromotive Fuel System + Imco Fuel Switch I have new in the boxes aeromotive marine fuel pump. 100 mic filter 10 mic filter $585.00 + shipping + a new in box IMCO 6 port fuel switch $600.00 + shipping.

I am finishing a rebuild of a Sanger flat. looking for suggestions or pics of starter and mag switch location and types. thanks for any help!

I took my 1988 Formula 206LS out for the first time this weekend (the only time before I have to winterize). The boat has a carbureted mercury 350 Magnum. Everything ran great in the beginning but eventually I was unable to shift into neutral. The control was very difficult to move and would...

Red powder coat with HD rocker switches. New in the box 65.00 352 620-8737

Hi all, I never installed a kill switch in my RaysonCraft and was wondering if there are good and bad locations? I have a Morse Control and was thinking behind it. Towards the stern. Also, are any of the kill switches better than the others? Thanks for any advice. --Jerry

Does the neutral switch on the 72c velvet drive work with the shift mechanism on the velvet drive case

What's the best route regarding your ignition switch? I see a minor advantage of a 4 position switch..is there a disadvantage?

Keep the same 650 cfm , wanted to see pictures of guys running 4 barrels d/p on tunnel rams .I need to figure out fuel line set up and routing and throttle linkage

Where is the best place to mount a kill switch in a flatbottom and how long should the lanyard be? Thinking about hitting a race or 2 next year and didnt know if there was a specific location the sanctioning bodies may require it to be. Seems to me like a bracket on the stringer just in front of...

I'm the original owner/builder of a 1974 Hallett 21' (v-drive) Day-Cruiser. The boat is powered by a 454 Chevy, driving through a Turbo 400 to Casale C-500 v-drive. The boat has the original fiberglass fuel tanks. I believe there are some advantages to E-85, but, I don't care to generate any...

Transom trim for Mercruiser. Plug and play. Has the flat weatherpack connectors. New, in box, with screws, instructions, etc. Should fit in a flat rate box so $50 shipped. $45 if you want to come pick it up. (I ordered the wrong one, some have a round connector, so rather than send it back...

Last time i took the boat out i noticed that the outdrive trim up would not work. Down worked fine and so did all the way up for trailer but not trim up? Its a standard 07 mercury dealio with the switch on the shifter, any input on where i should look first?

Does anybody know which post is c, no, nc there not marked on switch.

Dana marine dual button steering mount. Clear AO finish. Labeled trim and tabs up/down. Perfect condition. 140 new. 75.00 plus shipping.

I used this twice and paid little over 100.00 for it . 80.00 del.

Getting ready to wire up my boat and want to run a battery disconnect switch. I'm running just one battery. What are you guys all running that seems to work for you. Also remember, this is Washington so it may get wet as we drive in search of sun.... :raining: Thanks guys.....john